ATMEGA2560R231-CU Atmel, ATMEGA2560R231-CU Datasheet - Page 364

• Manufacturer Part Number: ATMEGA2560R231-CU
• Description: BUNDLE ATMEGA2560/RF231 PBGA
• Manufacturer: Atmel

Specifications of ATMEGA2560R231-CU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, RF4CE, SP100, WirelessHART™, ISM
• Data Interface: PCB, Surface Mount
• Memory Size: 256kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 100-CBGA and 32-QFN
• Processor Series: ATMEGA256x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 256 KB
• Data Ram Size: 8 KB
• Development Tools By Supplier: ATAVRRZ541, ATAVRRAVEN, ATAVRRZRAVEN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply: -
• Power - Output: -
• Operating Temperature: -
• Applications: -
• Sensitivity: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Details

29.9.15
29.9.16
29.9.17
2549M–AVR–09/10
Performing Chip Erase
Programming the Flash
Reading the Flash
1. Enter JTAG instruction PROG_COMMANDS.
2. Start Chip Erase using programming instruction 1a.
3. Poll for Chip Erase complete using programming instruction 1b, or wait for t
Before programming the Flash a Chip Erase must be performed, see “Performing Chip Erase”
on page 364.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash write using programming instruction 2a.
3. Load address Extended High byte using programming instruction 2b.
4. Load address High byte using programming instruction 2c.
5. Load address Low byte using programming instruction 2d.
6. Load data using programming instructions 2e, 2f and 2g.
7. Repeat steps 5 and 6 for all instruction words in the page.
8. Write the page using programming instruction 2h.
9. Poll for Flash write complete using programming instruction 2i, or wait for t
10. Repeat steps 3 to 9 until all data have been programmed.
A more efficient data transfer can be achieved using the PROG_PAGELOAD instruction:
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash write using programming instruction 2a.
3. Load the page address using programming instructions 2b, 2c and 2d. PCWORD (refer
4. Enter JTAG instruction PROG_PAGELOAD.
5. Load the entire page by shifting in all instruction words in the page byte-by-byte, starting
6. Enter JTAG instruction PROG_COMMANDS.
7. Write the page using programming instruction 2h.
8. Poll for Flash write complete using programming instruction 2i, or wait for t
9. Repeat steps 3 to 8 until all data have been programmed.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash read using programming instruction 3a.
3. Load address using programming instructions 3b, 3c and 3d.
4. Read data using programming instruction 3e.
5. Repeat steps 3 and 4 until all data have been read.
to
Table 29-14 on page
to
with the LSB of the first instruction in the page and ending with the MSB of the last
instruction in the page. Use Update-DR to copy the contents of the Flash Data Byte Reg-
ister into the Flash page location and to auto-increment the Program Counter before
each new word.
Table 29-14 on page
Table 29-14 on page
Table 29-7 on page
348).
348).
338) is used to address within one page and must be written as 0.
348).
ATmega640/1280/1281/2560/2561
WLRH_CE
WLRH
WLRH
(refer to
(refer to
(refer
364