EM2420-STR Ember, EM2420-STR Datasheet - Page 36

• Manufacturer Part Number: EM2420-STR
• Description: IC RF TXRX ZIGBEE 2.4GHZ 48-QLP
• Manufacturer: Ember

Specifications of EM2420-STR

• Mfg Application Notes: EM2420
• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: ZigBee™
• Power - Output: -3dBm
• Sensitivity: -94dBm
• Voltage - Supply: 2.1 V ~ 3.6 V
• Current - Receiving: 19.7mA
• Current - Transmitting: 17.4mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-QLP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Memory Size: -

Clear Channel Assessment section on
page 47 for details on CCA.
The preamble sequence is started 12
symbol periods after the command strobe.
After the programmable start of frame
delimiter has been transmitted, data is
fetched from the TXFIFO.
A TXFIFO underflow is issued if too few
bytes
Transmission
stopped. The underflow is indicated in the
TX_UNDERFLOW
returned during each address byte and
each byte written to the TXFIFO. The
underflow bit is only cleared by issuing a
SFLUSHTX command strobe.
The TXFIFO can only contain one data
frame at a given time.
After complete transmission of a data
frame, the TXFIFO is automatically refilled
with the last transmitted frame. Issuing a
new STXON or STXONCCA command
strobe will then cause the
retransmit the last frame.
Writing to the TXFIFO after a frame has
been transmitted will cause the TXFIFO to
be automatically flushed before the new
byte is written. The only exception is if a
TXFIFO underflow has occurred, when a
SFLUSHTX command strobe is required.
Buffered receive mode
In buffered receive mode (RX_MODE 0),
the 128 byte RXFIFO, located in the
EM2420
received by the demodulator. Accessing
data in the RXFIFO is described in the
FIFO access section on page 27.
The FIFO and FIFOP pins are used to
assist the microcontroller in supervising
the RXFIFO. Please note that the FIFO
and FIFOP pins are only related to the
RXFIFO, even if the
mode.
Ember Part Number: 120-0049-000D
are
RAM, is used to buffer data
written
is
status
EM2420
then
to
bit,
the
automatically
is in transmit
EM2420
which
TXFIFO.
EM2420 Datasheet
to
is
Multiple data frames may be in the
RXFIFO simultaneously, as long as the
total number of bytes does not exceed
128.
See the RXFIFO overflow section on page
29 for details on how an RXFIFO overflow
is detected and signaled.
Un-buffered, serial mode
Un-buffered mode should be used for
evaluation / debugging purposes only.
Buffered mode is recommended for all
applications.
In un-buffered mode, the FIFO and FIFOP
pins are reconfigured as data and data
clock pins. The TXFIFO and RXFIFO
buffers are not used in this mode. A
synchronous data clock is provided by the
EM2420
pin is used as data input/output. The
FIFOP clock frequency is 250 kHz when
active. This is illustrated in Figure 20.
In
(MDMCTRL1.TX_MODE=1),
synchronization sequence is inserted at
the start of each frame by hardware, as in
buffered mode. Data is sampled by the
EM2420
should be updated by the microcontroller
on the negative edge of FIFOP. See
Figure 20 for an illustration of the timing in
serial transmit mode. The SFD and CCA
pins retain their normal operation also in
serial mode. The
serial transmit mode until transmission is
turned off manually.
In
(MDMCTRL1.RX_MODE=1)
synchronization is still performed by the
EM2420
pin will remain idle low until a start of
frame delimiter has been detected.
. This means that the FIFOP clock
on the positive edge of FIFOP and
at the FIFOP pin, and the FIFO
serial
serial
EM2420
transmit
receive
EM2420
will remain in
Page 36 of 84
mode
mode
byte
a