ATMEGA64A-ANR Atmel, ATMEGA64A-ANR Datasheet - Page 316

• Manufacturer Part Number: ATMEGA64A-ANR
• Description: IC MCU AVR 64K FLASH 64TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA64A-ANR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

27.9.4
27.9.5
27.9.6
27.9.7
8160C–AVR–07/09
PROG_COMMANDS (0x5)
PROG_PAGELOAD (0x6)
PROG_PAGEREAD (0x7)
Data Registers
The AVR specific public JTAG instruction for entering programming commands via the JTAG
port. The 15-bit Programming Command Register is selected as data register. The active states
are the following:
The AVR specific public JTAG instruction to directly load the Flash data page via the JTAG port.
The 1024-bit Virtual Flash Page Load Register is selected as data register. This is a virtual scan
chain with length equal to the number of bits in one Flash page. Internally the Shift Register is 8-
bit. Unlike most JTAG instructions, the Update-DR state is not used to transfer data from the
Shift Register. The data are automatically transferred to the Flash page buffer byte-by-byte in
the Shift-DR state by an internal state machine. This is the only active state:
Note:
The AVR specific public JTAG instruction to read one full Flash data page via the JTAG port.
The 1032-bit Virtual Flash Page Read Register is selected as data register. This is a virtual scan
chain with length equal to the number of bits in one Flash page plus eight. Internally the Shift
Register is 8-bit. Unlike most JTAG instructions, the Capture-DR state is not used to transfer
data to the Shift Register. The data are automatically transferred from the Flash page buffer
byte-by-byte in the Shift-DR state by an internal state machine. This is the only active state:
Note:
The data registers are selected by the JTAG instruction registers described in section
ming Specific JTAG Instructions” on page
operations are:
• Update-DR: The programming enable signature is compared to the correct value, and
• Capture-DR: The result of the previous command is loaded into the data register.
• Shift-DR: The data register is shifted by the TCK input, shifting out the result of the previous
• Update-DR: The programming command is applied to the Flash inputs
• Run-Test/Idle: One clock cycle is generated, executing the applied command (not always
• Shift-DR: Flash page data are shifted in from TDI by the TCK input, and automatically loaded
• Shift-DR: Flash data are automatically read one byte at a time and shifted out on TDO by the
• Reset Register
• Programming Enable Register
• Programming Command Register
programming mode is entered if the signature is valid.
command and shifting in the new command.
required, see
into the Flash page one byte at a time.
TCK input. The TDI input is ignored.
The JTAG instruction PROG_PAGELOAD can only be used if the AVR device is the first device in
JTAG scan chain. If the AVR cannot be the first device in the scan chain, the byte-wise program-
ming algorithm must be used.
The JTAG instruction PROG_PAGEREAD can only be used if the AVR device is the first device in
JTAG scan chain. If the AVR cannot be the first device in the scan chain, the byte-wise program-
ming algorithm must be used.
Table 27-16 on page
319).
314. The data registers relevant for programming
ATmega64A
“Program-
316