LAN8710A-EZK-TR SMSC, LAN8710A-EZK-TR Datasheet - Page 10

• Manufacturer Part Number: LAN8710A-EZK-TR
• Description: Ethernet ICs 10/100 Ethernet XCVR w/HPAutoMDIX FlexPwr
• Manufacturer: SMSC
• Type: Single Chipr

Specifications of LAN8710A-EZK-TR

• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Transceivers
• Number Of Transceivers: 1
• Standard Supported: IEEE 802.3 or IEEE 802.3u
• Data Rate: 125 Mbps
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 1.6 V or 3 V
• Maximum Operating Temperature: + 85 C
• Package / Case: QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Revision 1.2 (11-10-10)
NUM PINS
1
1
1
1
1
1
1
(MII Mode)
(MII Mode)
(MII Mode)
(MII Mode)
(MII Mode)
Transmit
Transmit
Transmit
Transmit
Transmit
Transmit
Transmit
Transmit
Interrupt
Enable
NAME
Data 0
Data 1
Data 2
Data 3
Output
Data 4
Clock
Error
SYMBOL
TXCLK
TXD0
TXD1
TXD2
TXD3
TXER
TXD4
TXEN
nINT
Table 2.1 MII/RMII Signals
DATASHEET
Small Footprint MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX and flexPWR
BUFFER
TYPE
VO8
(PU)
(PU)
(PD)
VO8
VIS
VIS
VIS
VIS
VIS
VIS
VIS
10
The MAC transmits data to the transceiver using
this signal in all modes.
The MAC transmits data to the transceiver using
this signal in all modes.
The MAC transmits data to the transceiver using
this signal in MII Mode.
Note:
The MAC transmits data to the transceiver using
this signal in MII Mode.
Note:
Active low interrupt output. Place an external
resistor pull-up to VDDIO.
Note:
Note:
When driven high, the 4B/5B encode process
substitutes the Transmit Error code-group (/H/)
for the encoded data word. This input is ignored
in the 10BASE-T mode of operation.
In Symbol Interface (5B Decoding) mode, this
signal becomes the MII Transmit Data 4 line (the
MSB of the 5-bit symbol code-group).
Note:
Indicates that valid transmission data is present
on TXD[3:0]. In RMII Mode, only TXD[1:0]
provide valid data.
Used to latch data from the MAC into the
transceiver.
Note:
MII (100BASE-TX): 25MHz
MII (10BASE-T): 2.5MHz
This signal must be grounded in RMII
Mode.
This signal must be grounded in RMII
Mode.
Refer to
Management," on page 33
details on device interrupts.
Refer to
LED2 Polarity Selection," on page 38
details on how the nINTSEL
configuration strap is used to determine
the function of this pin.
This signal is not used in RMII Mode.
This signal is not used in RMII Mode.
DESCRIPTION
Section 3.8.1.2, "nINTSEL and
Section 3.6, "Interrupt
SMSC LAN8710A/LAN8710Ai
for additional
Datasheet
®
Technology
for