AD9522-1BCPZ-REEL7 Analog Devices Inc, AD9522-1BCPZ-REEL7 Datasheet - Page 6

• Manufacturer Part Number: AD9522-1BCPZ-REEL7
• Description: 12- Channel Clock Generator W/Int VCO
• Manufacturer: Analog Devices Inc
• Type: Clock Generator, Fanout Distributionr

Specifications of AD9522-1BCPZ-REEL7

• Pll: Yes
• Input: CMOS, LVDS, LVPECL
• Output: CMOS, LVDS
• Number Of Circuits: 1
• Ratio - Input:output: 2:12, 2:24
• Differential - Input:output: Yes/Yes
• Frequency - Max: 2.65GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3.135 V ~ 3.465 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LFCSP
• Frequency-max: 2.5GHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD9522-1
Parameter
PHASE OFFSET IN ZERO DELAY
NOISE CHARACTERISTICS
PLL DIGITAL LOCK DETECT WINDOW
1
2
The REFIN and REFIN self-bias points are offset slightly to avoid chatter on an open input condition.
For reliable operation of the digital lock detect, the period of the PFD frequency must be greater than the unlock-after-lock time.
In-Band Phase Noise of the Charge Pump/
PLL Figure of Merit (FOM)
Lock Threshold (Coincidence of Edges)
Unlock Threshold (Hysteresis)
Phase Offset (REF-to-LVDS Clock Output
Phase Offset (REF-to-LVDS Clock Output
Phase Offset (REF-to-CLK Input Pins) in
Phase Offset (REF-to-CLK Input Pins) in
Pins) in Internal Zero Delay Mode
Pins) in Internal Zero Delay Mode
External Zero Delay Mode
External Zero Delay Mode
Phase Frequency Detector (In-Band
Means Within the LBW of the PLL)
@ 500 kHz PFD Frequency
@ 1 MHz PFD Frequency
@ 10 MHz PFD Frequency
@ 50 MHz PFD Frequency
Low Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 6.0 ns)
Low Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 1.3 ns, 2.9 ns)
High Range (ABP 6.0 ns)
2
2
Min
1890
900
318
−329
Typ
2348
1217
677
+33
−165
−162
−152
−144
−222
3.5
7.5
3.5
7
15
11
Rev. 0 | Page 6 of 84
Max
3026
1695
1085
+360
Unit
ps
ps
ps
ps
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
ns
ns
ns
ns
ns
ns
Test Conditions/Comments
REF refers to REFIN (REF1)/REFIN (REF2)
When N delay and R delay are bypassed
When N delay = Setting 111 and R delay is bypassed
When N delay and R delay are bypassed
When N delay = Setting 011 and R delay is bypassed
The PLL in-band phase noise floor is estimated by
measuring the in-band phase noise at the output of
the VCO and subtracting 20 log(N) (where N is the value
of the N divider)
Reference slew rate > 0.5 V/ns; FOM + 10 log(f
approximation of the PFD/CP in-band phase noise (in
the flat region) inside the PLL loop bandwidth; when
running closed-loop, the phase noise, as observed at
the VCO output, is increased by 20 log(N); PLL figure of
merit decreases with decreasing slew rate; see Figure 12
Signal available at the LD, STATUS, and REFMON pins
when selected by appropriate register settings; lock
detect window settings can be varied by changing the
CPRSET resistor
Selected by 0x017[1:0] and 0x018[4] (this is the threshold
to go from unlock to lock)
0x017[1:0] = 00b, 01b, 11b; 0x018[4] = 1b
0x017[1:0] = 00b, 01b, 11b; 0x018[4] = 0b
0x017[1:0] = 10b; 0x018[4] = 0b
Selected by 0x017[1:0] and 0x018[4] (this is the threshold
to go from lock to unlock)
0x017[1:0] = 00b, 01b, 11b; 0x018[4] = 1b
0x017[1:0] = 00b, 01b, 11b; 0x018[4] = 0b
0x017[1:0] = 10b; 0x018[4] = 0b
PFD
) is an