LAN9115-MT Standard Microsystems (SMSC), LAN9115-MT Datasheet - Page 32

• Manufacturer Part Number: LAN9115-MT
• Manufacturer: Standard Microsystems (SMSC)

Specifications of LAN9115-MT

• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (min): 2.97V
• Operating Supply Voltage (max): 3.63V
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 100
• Lead Free Status / RoHS Status: Compliant

Revision 1.5 (07-11-08)
3.8
3.9
3.9.1
MODE OF OPERATION
The General Purpose Timer is a programmable block that can be used to generate periodic host
interrupts. The resolution of this timer is 100uS.
The GP Timer loads the GPT_CNT Register with the value in the GPT_LOAD field and begins counting
down when the TIMER_EN bit is set to a ‘1.’ On a reset, or when the TIMER_EN bit changes from
set ‘1’ to cleared ‘0,’ the GPT_CNT field is initialized to FFFFh. The GPT_CNT register is also initialized
to FFFFh on a reset. Software can write the pre-load value into the GPT_LOAD field at any time; e.g.,
before or after the TIMER_EN bit is asserted. The GPT Enable bit TIMER_EN is located in the
GPT_CFG register.
Once enabled, the GPT counts down either until it reaches 0000h or until a new pre-load value is
written to the GPT_LOAD field. At 0000h, the counter wraps around to FFFFh, asserts the GPT
interrupt status bit and the IRQ signal if the GPT_INT_EN bit is set, and continues counting. The GPT
interrupt status bit is in the INT_STS Register. The GPT_INT hardware interrupt can only be set if the
GPT_INT_EN bit is set. GPT_INT is a sticky bit (R/WC); i.e., once the GPT_INT bit is set, it can only
be cleared by writing a ‘1’ to the bit.
LAN9115 can optionally load its MAC address from an external serial EEPROM. If a properly
configured EEPROM is detected by LAN9115 at power-up, hard reset or soft reset, the ADDRH and
ADDRL registers will be loaded with the contents of the EEPROM. If a properly configured EEPROM
is not detected, it is the responsibility of the host LAN Driver to set the IEEE addresses.
The LAN9115 EEPROM controller also allows the host system to read, write and erase the contents
of the Serial EEPROM. The EEPROM controller supports most “93C46” type EEPROMs configured for
128 x 8-bit operation.
MAC Address Auto-Load
On power-up, hard reset or soft reset, the EEPROM controller attempts to read the first byte of data
from the EEPROM (address 00h). If the value A5h is read from the first address, then the EEPROM
controller will assume that an external Serial EEPROM is present. The EEPROM controller will then
access the next EEPROM byte and send it to the MAC Address register byte 0 (ADDRL[7:0]). This
process will be repeated for the next five bytes of the MAC Address, thus fully programming the 48-
bit MAC address. Once all six bytes have been programmed, the “MAC Address Loaded” bit is set in
the E2P_CMD register. A detailed explanation of the EEPROM byte ordering with respect to the MAC
address is given in
If an 0xA5h is not read from the first address, the EEPROM controller will end initialization. It is then
the responsibility of the host LAN driver software to set the IEEE address by writing to the MAC’s
ADDRH and ADDRL registers.
The host can initiate a reload of the MAC address from the EEPROM by issuing the RELOAD
command via the E2P command (E2P_CMD) register. If the first byte read from the EEPROM is not
A5h, it is assumed that the EEPROM is not present, or not programmed, and the MAC address reload
will fail. The “MAC Address Loaded” bit indicates a successful reload of the MAC address.
General Purpose Timer (GP Timer)
EEPROM Interface
A1 = 0
A1 = 1
D[15:8]
Byte 1
Byte 3
Section 5.4.3, "ADDRL—MAC Address Low Register," on page
Table 3.7 Byte Lane Mapping (continued)
DATA PINS
DATASHEET
Byte 0
Byte 2
D[7:0]
32
Highly Efficient Single-Chip 10/100 Non-PCI Ethernet Controller
Note:
This mode can also be used by native 16-
bit processors.
DESCRIPTION
102.
SMSC LAN9115
Datasheet