LAN9115-MT Standard Microsystems (SMSC), LAN9115-MT Datasheet - Page 99
![no-image](/images/manufacturer_photos/0/6/632/standard_microsystems__smsc__sml.jpg)
LAN9115-MT
Manufacturer Part Number
LAN9115-MT
Description
Manufacturer
Standard Microsystems (SMSC)
Datasheet
1.LAN9115-MT.pdf
(136 pages)
Specifications of LAN9115-MT
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (min)
2.97V
Operating Supply Voltage (max)
3.63V
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
100
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LAN9115-MT
Manufacturer:
Standard
Quantity:
1 907
Company:
Part Number:
LAN9115-MT
Manufacturer:
SMSC
Quantity:
672
Company:
Part Number:
LAN9115-MT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
LAN9115-MT
Manufacturer:
SMSC
Quantity:
20 000
Company:
Part Number:
LAN9115-MT-E2
Manufacturer:
SMSC
Quantity:
3 994
Part Number:
LAN9115-MT-E2
Manufacturer:
SMSC
Quantity:
20 000
Highly Efficient Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
SMSC LAN9115
5.4.1
30-24
BITS
31
23
22
21
20
19
18
17
16
15
14
Receive All Mode (RXALL). When set, all incoming packets will be received and passed on to the
address filtering Function for processing of the selected filtering mode on the received frame. Address
filtering then occurs and is reported in Receive Status. When reset, only frames that pass Destination
Address filtering will be sent to the Application.
Reserved
Disable Receive Own (RCVOWN). When set, the MAC disables the reception of frames when the
MII TX_EN signal is asserted. The MAC blocks the transmitted frame on the receive path. When reset,
the MAC receives all packets the PHY gives, including those transmitted by the MAC.This bit should
be reset when the Full Duplex Mode bit is set.
Reserved
Loopback operation Mode (LOOPBK). Selects the loop back operation modes for the MAC. This is
only for full duplex mode
1’b0: Normal: No feedback
1’b1: Internal: Through MII
In internal loopback mode, the TX frame is received by the Internal MII interface, and sent back to
the MAC without being sent to the PHY.
Note:
Full Duplex Mode (FDPX). When set, the MAC operates in Full-Duplex mode, in which it can transmit
and receive simultaneously. In Full-Duplex mode, the heartbeat check is disabled and the heartbeat
fail status should thus be ignored.
Pass All Multicast (MCPAS). When set, indicates that all incoming frames with a Multicast destination
address (first bit in the destination address field is 1) are received. Incoming frames with physical
address (Individual Address/Unicast) destinations are filtered and received only if the address matches
the MAC Address.
Promiscuous Mode (PRMS). When set, indicates that any incoming frame is received regardless of
its destination address.
Inverse filtering (INVFILT). When set, the address check Function operates in Inverse filtering mode.
This is valid only during Perfect filtering mode.
Pass Bad Frames (PASSBAD). When set, all incoming frames that passed address filtering are
received, including runt frames and collided frames.
Hash Only Filtering mode (HO). When set, the address check Function operates in the Imperfect
Address Filtering mode both for physical and multicast addresses
Reserved
MAC_CR—MAC Control Register
This register establishes the RX and TX operation modes and controls for address filtering and packet
filtering.
Offset:
Default Value:
When enabling or disabling the loopback mode it can take up to 10μs for the mode change
to occur. The transmitter and receiver must be stopped and disabled when modifying the
LOOPBK bit. The transmitter or receiver should not be enabled within10μs of modifying the
LOOPBK bit.
1
00040000h
DATASHEET
DESCRIPTION
99
Attribute:
Size:
R/W
32 bits
Revision 1.5 (07-11-08)