MT29F1G08ABADAH4:D Micron Technology Inc, MT29F1G08ABADAH4:D Datasheet - Page 40
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT29F1G08ABADAH4:D
Manufacturer Part Number
MT29F1G08ABADAH4:D
Description
MICMT29F1G08ABADAH4:D 1GB SLC NAND BGA
Manufacturer
Micron Technology Inc
Datasheet
1.MT29F1G08ABADAH4D.pdf
(93 pages)
Specifications of MT29F1G08ABADAH4:D
Cell Type
NAND
Density
8Gb
Interface Type
Parallel
Address Bus
27b
Operating Supply Voltage (typ)
3.3V
Operating Temp Range
0C to 70C
Package Type
VFBGA
Sync/async
Asynchronous
Operating Temperature Classification
Commercial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Word Size
8b
Number Of Words
128M
Supply Current
35mA
Mounting
Surface Mount
Pin Count
63
Lead Free Status / Rohs Status
Supplier Unconfirmed
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT29F1G08ABADAH4:D
Manufacturer:
ROHM
Quantity:
1 001
Company:
Part Number:
MT29F1G08ABADAH4:D
Manufacturer:
MICRON
Quantity:
2 690
Company:
Part Number:
MT29F1G08ABADAH4:D
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Feature Operations
PDF: 09005aef83e5ffed
m68a.pdf – Rev. D 06/10 EN
The SET FEATURES (EFh) and GET FEATURES (EEh) commands are used to modify the
target's default power-on behavior. These commands use a one-byte feature address to
determine which subfeature parameters will be read or modified. Each feature address
(in the 00h to FFh range) is defined in below. The SET FEATURES (EFh) command
writes subfeature parameters (P1–P4) to the specified feature address. The GET FEA-
TURES command reads the subfeature parameters (P1–P4) at the specified feature
address.
When a feature is set, by default it remains active until the device is power cycled. It is
volatile. Unless otherwise specified in the features table, once a device is set it remains
set, even if a RESET (FFh) command is issued. GET/SET FEATURES commands can be
used after required RESET to enable features before system BOOT ROM process.
Internal ECC can be enabled/disabled using SET FEATURES (EFh). The SET FEATURES
command (EFh), followed by address 90h, followed by four data bytes (only the first
data byte is used) will enable/disable internal ECC.
The sequence to enable internal ECC with SET FEATURES is EFh(cmd)-90h(addr)-
08h(data)-00h(data)-00h(data)-00h(data)-wait(
The sequence to disable internal ECC with SET FEATURES is EFh(cmd)-90h(addr)-
00h(data)-00h(data)-00h(data)-00h(data)-wait(
is EEh.
Table 9: Feature Address Definitions
Feature Address
02h–7Fh
82h–FFh
00h
01h
80h
81h
90h
Definition
Reserved
Timing mode
Reserved
Programmable output drive strength
Programmable RB# pull-down strength
Reserved
Array operation mode
40
Micron Technology, Inc. reserves the right to change products or specifications without notice.
1Gb x8, x16: NAND Flash Memory
t
t
FEAT).
FEAT). The GET FEATURES command
Feature Operations
© 2010 Micron Technology, Inc. All rights reserved.