MT29F1G08ABADAH4:D Micron Technology Inc, MT29F1G08ABADAH4:D Datasheet - Page 50
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT29F1G08ABADAH4:D
Manufacturer Part Number
MT29F1G08ABADAH4:D
Description
MICMT29F1G08ABADAH4:D 1GB SLC NAND BGA
Manufacturer
Micron Technology Inc
Datasheet
1.MT29F1G08ABADAH4D.pdf
(93 pages)
Specifications of MT29F1G08ABADAH4:D
Cell Type
NAND
Density
8Gb
Interface Type
Parallel
Address Bus
27b
Operating Supply Voltage (typ)
3.3V
Operating Temp Range
0C to 70C
Package Type
VFBGA
Sync/async
Asynchronous
Operating Temperature Classification
Commercial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Word Size
8b
Number Of Words
128M
Supply Current
35mA
Mounting
Surface Mount
Pin Count
63
Lead Free Status / Rohs Status
Supplier Unconfirmed
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MT29F1G08ABADAH4:D
Manufacturer:
ROHM
Quantity:
1 001
Company:
Part Number:
MT29F1G08ABADAH4:D
Manufacturer:
MICRON
Quantity:
2 690
Company:
Part Number:
MT29F1G08ABADAH4:D
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Read Operations
PDF: 09005aef83e5ffed
m68a.pdf – Rev. D 06/10 EN
The READ PAGE (00h-30h) command, when issued by itself, reads one page from the
NAND Flash array to its cache register and enables data output for that cache register.
During data output the following commands can be used to read and modify the data
in the cache registers: RANDOM DATA READ (05h-E0h) and RANDOM DATA INPUT
(85h).
Read Cache Operations
To increase data throughput, the READ PAGE CACHE series (31h, 00h-31h) commands
can be used to output data from the cache register while concurrently copying a page
from the NAND Flash array to the data register.
To begin a read page cache sequence, begin by reading a page from the NAND Flash
array to its corresponding cache register using the READ PAGE (00h-30h) command.
R/B# goes LOW during
t
• READ PAGE CACHE SEQUENTIAL (31h) – copies the next sequential page from the
• READ PAGE CACHE RANDOM (00h-31h) – copies the page specified in this command
After the READ PAGE CACHE series (31h, 00h-31h) command has been issued, R/B#
goes LOW on the target, and RDY = 0 and ARDY = 0 on the die (LUN) for
the next page begins copying data from the array to the data register. After
R/B# goes HIGH and the die’s (LUN’s) status register bits indicate the device is busy
with a cache operation (RDY = 1, ARDY = 0). The cache register becomes available and
the page requested in the READ PAGE CACHE operation is transferred to the data regis-
ter. At this point, data can be output from the cache register, beginning at column
address 0. The RANDOM DATA READ (05h-E0h) command can be used to change the
column address of the data output by the die (LUN).
After outputting the desired number of bytes from the cache register, either an addition-
al READ PAGE CACHE series (31h, 00h-31h) operation can be started or the READ PAGE
CACHE LAST (3Fh) command can be issued.
If the READ PAGE CACHE LAST (3Fh) command is issued, R/B# goes LOW on the tar-
get, and RDY = 0 and ARDY = 0 on the die (LUN) for
copied into the cache register. After
ARDY = 1, indicating that the cache register is available and that the die (LUN) is ready.
Data can then be output from the cache register, beginning at column address 0. The
RANDOM DATA READ (05h-E0h) command can be used to change the column address
of the data being output.
For READ PAGE CACHE series (31h, 00h-31h, 3Fh), during the die (LUN) busy time,
t
(70h) and RESET (FFh). When RDY = 1 and ARDY = 0, the only valid commands during
READ PAGE CACHE series (31h, 00h-31h) operations are status operations (70h), READ
MODE (00h), READ PAGE CACHE series (31h, 00h-31h), RANDOM DATA READ (05h-
E0h), and RESET (FFh).
R (R/B# is HIGH and RDY = 1, ARDY = 1), issue either of these commands:
RCBSY, when RDY = 0 and ARDY = 0, the only valid commands are status operations
NAND Flash array to the data register
from the NAND Flash array to its corresponding data register
t
R and the selected die (LUN) is busy (RDY = 0, ARDY = 0). After
50
t
RCBSY, R/B# goes HIGH and RDY = 1 and
Micron Technology, Inc. reserves the right to change products or specifications without notice.
1Gb x8, x16: NAND Flash Memory
t
RCBSY while the data register is
© 2010 Micron Technology, Inc. All rights reserved.
Read Operations
t
RCBSY while
t
RCBSY,