PIC24FJ256DA210-I/PT Microchip Technology Inc., PIC24FJ256DA210-I/PT Datasheet - Page 327

• Manufacturer Part Number: PIC24FJ256DA210-I/PT
• Description: 100 TQFP 12x12x1mm TRAY, 16-bit, 256KB Flash, 96K RAM, USB, Graphics
• Manufacturer: Microchip Technology Inc.

Specifications of PIC24FJ256DA210-I/PT

• A/d Inputs: 24 Channel, 10-Bit
• Comparators: 3
• Cpu Speed: 16 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 84
• Interface: I2C/SPI/UART
• Memory Capacity: 256 Kbytes
• Memory Type: Flash
• Number Of Bits: 16
• Number Of Leads: 100
• Number Of Pins: 100
• Package Type: 100-Pin TQFP
• Programmable Memory: 256K Bytes
• Ram Size: 96K Bytes
• Speed: 32 MHz
• Temperature Range: –40 to +85 °C
• Timers: 5-16-bit
• Voltage, Range: 2.2-3.6 V
• Voltage, Rating: 2.2-3.6 V
• Run Mode: 800 μA/MIPS, 3.3 V Typical
• Standby Current With 32 Khz Oscillator: 22 μA, 3.3 V Typical
• Lead Free Status / Rohs Status: RoHS Compliant part

REGISTER 23-1:
 2010 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12-10
bit 9-8
bit 7-5
bit 4-3
bit 2
bit 1
bit 0
Note 1:
ADON
SSRC2
R/W-0
R/W-0
(1)
The values of the ADC1BUFx registers will not retain their values once the ADON bit is cleared. Read out
the conversion values from the buffer before disabling the module.
ADON: A/D Operating Mode bit
1 = A/D Converter module is operating
0 = A/D Converter is off
Unimplemented: Read as ‘0’
ADSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
Unimplemented: Read as ‘0’
FORM<1:0>: Data Output Format bits
11 = Signed fractional (sddd dddd dd00 0000)
10 = Fractional (dddd dddd dd00 0000)
01 = Signed integer (ssss sssd dddd dddd)
00 = Integer (0000 00dd dddd dddd)
SSRC<2:0>: Conversion Trigger Source Select bits
111 = Internal counter ends sampling and starts conversion (auto-convert)
110 = CTMU event ends sampling and starts conversion
101 = Reserved
100 = Timer5 compare ends sampling and starts conversion
011 = Reserved
010 = Timer3 compare ends sampling and starts conversion
001 = Active transition on INT0 pin ends sampling and starts conversion
000 = Clearing SAMP bit ends sampling and starts conversion
Unimplemented: Read as ‘0’
ASAM: A/D Sample Auto-Start bit
1 = Sampling begins immediately after the last conversion completes. The SAMP bit is auto-set.
0 = Sampling begins when the SAMP bit is set
SAMP: A/D Sample Enable bit
1 = A/D sample/hold amplifier is sampling input
0 = A/D sample/hold amplifier is holding
DONE: A/D Conversion Status bit
1 = A/D conversion is done
0 = A/D conversion is NOT done
SSRC1
R/W-0
U-0
—
AD1CON1: A/D CONTROL REGISTER 1
HSC = Hardware Settable/Clearable bit
W = Writable bit
‘1’ = Bit is set
ADSIDL
SSRC0
R/W-0
R/W-0
(1)
PIC24FJ256DA210 FAMILY
U-0
U-0
—
—
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
U-0
U-0
—
—
R/W-0
ASAM
U-0
—
x = Bit is unknown
R-0, HSC
FORM1
SAMP
R/W-0
DS39969B-page 327
R-0, HSC
FORM0
R/W-0
DONE
bit 8
bit 0