PIC24FJ256GB206-I/MR Microchip Technology Inc., PIC24FJ256GB206-I/MR Datasheet - Page 228

• Manufacturer Part Number: PIC24FJ256GB206-I/MR
• Description: 16-bit, 256KB Flash, 96K RAM, USB, 64 QFN 9x9x0.9mm TUBE
• Manufacturer: Microchip Technology Inc.

Specifications of PIC24FJ256GB206-I/MR

• A/d Inputs: 16 Channel, 10-bit
• Comparators: 3
• Cpu Speed: 16 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 52
• Interface: I2C/SPI/UART/USART/USB
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 64-pin QFN
• Programmable Memory: 256K Bytes
• Ram Size: 98K Bytes
• Speed: 32 MHz
• Temperature Range: –40 to 85 °C
• Timers: 5-16-bit
• Voltage, Range: 2.2-3.6 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC24FJ256GB210 FAMILY
REGISTER 17-1:
DS39975A-page 228
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9-8
bit 7
bit 6
bit 5
Note 1:
UARTEN
R/W-0, HC
R/W-0
WAKE
2:
(1)
If UARTEN = 1, the peripheral inputs and outputs must be configured to an available RPn/RPIn pin. See
Section 10.4 “Peripheral Pin Select (PPS)” for more information.
This feature is only available for the 16x BRG mode (BRGH = 0).
UARTEN: UARTx Enable bit
1 = UARTx is enabled; all UARTx pins are controlled by UARTx as defined by UEN<1:0>
0 = UARTx is disabled; all UARTx pins are controlled by port latches; UARTx power consumption is minimal
Unimplemented: Read as ‘0’
USIDL: Stop in Idle Mode bit
1 = Discontinue module operation when device enters Idle mode
0 = Continue module operation in Idle mode
IREN: IrDA
1 = IrDA encoder and decoder are enabled
0 = IrDA encoder and decoder are disabled
RTSMD: Mode Selection for UxRTS Pin bit
1 = UxRTS pin is in Simplex mode
0 = UxRTS pin is in Flow Control mode
Unimplemented: Read as ‘0’
UEN<1:0>: UARTx Enable bits
11 = UxTX, UxRX and BCLKx pins are enabled and used; UxCTS pin is controlled by port latches
10 = UxTX, UxRX, UxCTS and UxRTS pins are enabled and used
01 = UxTX, UxRX and UxRTS pins are enabled and used; UxCTS pin is controlled by port latches
00 = UxTX and UxRX pins are enabled and used; UxCTS and UxRTS/BCLKx pins are controlled by port
WAKE: Wake-up on Start Bit Detect During Sleep Mode Enable bit
1 = UARTx will continue to sample the UxRX pin; interrupt is generated on the falling edge, bit is cleared
0 = No wake-up is enabled
LPBACK: UARTx Loopback Mode Select bit
1 = Enable Loopback mode
0 = Loopback mode is disabled
ABAUD: Auto-Baud Enable bit
1 = Enable baud rate measurement on the next character – requires reception of a sync field (55h);
0 = Baud rate measurement is disabled or completed
LPBACK
R/W-0
in hardware on the following rising edge
cleared in hardware upon completion
U-0
—
latches
UxMODE: UARTx MODE REGISTER
®
Encoder and Decoder Enable bit
HC = Hardware Clearable bit
W = Writable bit
‘1’ = Bit is set
R/W-0, HC
ABAUD
USIDL
R/W-0
(1)
IREN
RXINV
R/W-0
R/W-0
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
(2)
RTSMD
R/W-0
R/W-0
BRGH
PDSEL1
R/W-0
U-0
—
 2010 Microchip Technology Inc.
x = Bit is unknown
PDSEL0
R/W-0
UEN1
R/W-0
STSEL
R/W-0
R/W-0
UEN0
bit 8
bit 0