PIC24FJ256GB206-I/MR Microchip Technology Inc., PIC24FJ256GB206-I/MR Datasheet - Page 321

• Manufacturer Part Number: PIC24FJ256GB206-I/MR
• Description: 16-bit, 256KB Flash, 96K RAM, USB, 64 QFN 9x9x0.9mm TUBE
• Manufacturer: Microchip Technology Inc.

Specifications of PIC24FJ256GB206-I/MR

• A/d Inputs: 16 Channel, 10-bit
• Comparators: 3
• Cpu Speed: 16 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 52
• Interface: I2C/SPI/UART/USART/USB
• Memory Type: Flash
• Number Of Bits: 16
• Package Type: 64-pin QFN
• Programmable Memory: 256K Bytes
• Ram Size: 98K Bytes
• Speed: 32 MHz
• Temperature Range: –40 to 85 °C
• Timers: 5-16-bit
• Voltage, Range: 2.2-3.6 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

REGISTER 25-1:
 2010 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 10
bit 10
bit 9
bit 8
bit 7
bit 6-5
bit 4
Note 1:
EDG2POL
CTMUEN
R/W-0
R/W-0
If TGEN = 1, the peripheral inputs and outputs must be configured to an available RPn/RPIn pin. See
Section 10.4 “Peripheral Pin Select (PPS)” for more information.
CTMUEN: CTMU Enable bit
1 = Module is enabled
0 = Module is disabled
Unimplemented: Read as ‘0’
CTMUSIDL: Stop in Idle Mode bit
1 = Discontinue module operation when the device enters Idle mode
0 = Continue module operation in Idle mode
TGEN: Time Generation Enable bit
1 = Enables edge delay generation
0 = Disables edge delay generation
EDGEN: Edge Enable bit
1 = Edges are not blocked
0 = Edges are blocked
EDGSEQEN: Edge Sequence Enable bit
1 = Edge 1 event must occur before Edge 2 event can occur
0 = No edge sequence is needed
IDISSEN: Analog Current Source Control bit
1 = Analog current source output is grounded
0 = Analog current source output is not grounded
CTTRIG: Trigger Control bit
1 = Trigger output is enabled
0 = Trigger output is disabled
EDG2POL: Edge 2 Polarity Select bit
1 = Edge 2 is programmed for a positive edge response
0 = Edge 2 is programmed for a negative edge response
EDG2SEL<1:0>: Edge 2 Source Select bits
11 = CTEDG1 pin
10 = CTEDG2 pin
01 = OC1 module
00 = Timer1 module
EDG1POL: Edge 1 Polarity Select bit
1 = Edge 1 is programmed for a positive edge response
0 = Edge 1 is programmed for a negative edge response
EDG2SEL1
R/W-0
U-0
—
CTMUCON: CTMU CONTROL REGISTER
HSC = Hardware Settable/Clearable bit
W = Writable bit
‘1’ = Bit is set
CTMUSIDL
EDG2SEL0
R/W-0
R/W-0
EDG1POL
PIC24FJ256GB210 FAMILY
TGEN
R/W-0
R/W-0
(1)
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
EDG1SEL1
EDGEN
R/W-0
R/W-0
EDGSEQEN
EDG1SEL0
R/W-0
R/W-0
x = Bit is unknown
R/W-0, HSC R/W-0, HSC
EDG2STAT
IDISSEN
R/W-0
DS39975A-page 321
EDG1STAT
CTTRIG
R/W-0
bit 8
bit 0