PIC16F72-I/SO Microchip Technology Inc., PIC16F72-I/SO Datasheet - Page 47
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
PIC16F72-I/SO
Manufacturer Part Number
PIC16F72-I/SO
Description
28 PIN, 3.5 KB FLASH, 128 RAM, 22 I/O
Manufacturer
Microchip Technology Inc.
Datasheet
1.PIC16F72-ISO.pdf
(136 pages)
Specifications of PIC16F72-I/SO
A/d Inputs
5-Channel, 8-Bit
Cpu Speed
5 MIPS
Eeprom Memory
0 Bytes
Input Output
22
Interface
I2C/SPI
Memory Type
Flash
Number Of Bits
8
Package Type
28-pin SOIC
Programmable Memory
3.5K Bytes
Ram Size
128 Bytes
Speed
20 MHz
Timers
2-8-bit, 1-16-bit
Voltage, Range
2-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part
Electrostatic Device
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16F72-I/SO
Manufacturer:
MICROCHIP
Quantity:
3 290
Part Number:
PIC16F72-I/SO
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
REGISTER 9-2:
2002 Microchip Technology Inc.
bit 7
bit 6
bit 5
bit 4
bit 3-0
SSPCON: SYNC SERIAL PORT CONTROL REGISTER (ADDRESS 14h)
bit 7
WCOL: Write Collision Detect bit
1 = The SSPBUF register is written while it is still transmitting the previous word (must be
0 = No collision
SSPOV: Receive Overflow Indicator bit
In SPI mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case
0 = No overflow
In I
1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV
0 = No overflow
SSPEN: Synchronous Serial Port Enable bit
In SPI mode:
1 = Enables serial port and configures SCK, SDO, and SDI as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
In I
1 = Enables the serial port and configures the SDA and SCL pins as serial port pins
0 = Disables serial port and configures these pins as I/O port pins
In both modes, when enabled, these pins must be properly configured as input or output.
CKP: Clock Polarity Select bit
In SPI mode:
1 = IDLE state for clock is a high level (Microwire
0 = IDLE state for clock is a low level (Microwire alternate)
In I
SCK release control
1 = Enable clock
0 = Holds clock low (clock stretch - used to ensure data setup time)
SSPM<3:0>: Synchronous Serial Port Mode Select bits
0000 = SPI Master mode, clock = F
0001 = SPI Master mode, clock = F
0010 = SPI Master mode, clock = F
0011 = SPI Master mode, clock = TMR2 output/2
0100 = SPI Slave mode, clock = SCK pin. SS pin control enabled.
0101 = SPI Slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin.
0110 = I
0111 = I
1011 = I
1110 = I
1111 = I
Legend:
R = Readable bit
- n = Value at POR
WCOL
R/W-0
2
2
2
cleared in software)
C mode:
C mode:
C mode:
of overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user
must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In Master
mode, the overflow bit is not set since each new reception (and transmission) is initiated
by writing to the SSPBUF register.
is a "don’t care" in Transmit mode. SSPOV must be cleared in software in either mode.
2
2
2
2
2
C Slave mode, 7-bit address
C Slave mode, 10-bit address
C firmware controlled Master mode (Slave IDLE)
C Slave mode, 7-bit address with START and STOP bit interrupts enabled
C Slave mode, 10-bit address with START and STOP bit interrupts enabled
SSPOV
R/W-0
SSPEN
R/W-0
W = Writable bit
‘1’ = Bit is set
OSC
OSC
OSC
R/W-0
CKP
/4
/16
/64
®
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
default)
SSPM3
R/W-0
SSPM2
R/W-0
PIC16F72
x = Bit is unknown
SSPM1
R/W-0
DS39597B-page 45
SSPM0
R/W-0
bit 0