M471B5773DH0-YK0 Samsung Semiconductor, M471B5773DH0-YK0 Datasheet - Page 16

• Manufacturer Part Number: M471B5773DH0-YK0
• Manufacturer: Samsung Semiconductor

Specifications of M471B5773DH0-YK0

• Lead Free Status / Rohs Status: Supplier Unconfirmed

Unbuffered SODIMM
10.3.3 Single-ended Requirements for Differential Signals
Each individual component of a differential signal (CK, DQS, CK, DQS) has also to comply with certain requirements for single-ended signals.
CK and CK have to approximately reach V
half-cycle.
DQS have to reach V
valid transition.
Note that the applicable ac-levels for ADD/CMD and DQ’s might be different per speed-bin etc. E.g. if V
signals, then these ac-levels apply also for the single-ended signals CK and CK .
Note that while ADD/CMD and DQ signal requirements are with respect to V
with respect to V
ended components of differential signals the requirement to reach V
mode characteristics of these signals.
[ Table 5 ] Single ended levels for CK, DQS, CK, DQS
NOTE :
1. For CK, CK use V
2. V
3. These values are not defined, however the single-ended signals CK, CK, DQS, DQS need to be within the respective limits (V
reduced level applies also here
nals as well as the limitations for overshoot and undershoot. Refer to "Overshoot and Undershoot Specification"
IH
(AC)/V
Symbol
V
V
SEH
SEL
IL
(AC) for DQs is based on V
DD
IH
/2; this is nominally the same. The transition of single-ended signals through the ac-levels is used to measure setup time. For single-
/V
SEH
IL
Single-ended high-level for CK, CK
Single-ended high-level for strobes
(AC) of ADD/CMD; for strobes (DQS, DQS) use V
Single-ended low-level for strobes
Single-ended low-level for CK, CK
V
min / V
DD
V
/2 or V
V
DD
SS
V
V
SEL
SEL
or V
SEH
or V
Parameter
max (approximately the ac-levels ( V
DDQ
REFDQ
max
DDQ
SSQ
min
/2
; V
SEH
IH
(AC)/V
min / V
Figure 3. Single-ended requirement for differential signals
IL
(AC) for ADD/CMD is based on V
SEL
max (approximately equal to the ac-levels ( V
datasheet
IH
/V
V
SEL
IL
SEH
(AC) of DQs.
(V
(V
IH
max, V
(AC) / V
DD
DD
NOTE 3
NOTE 3
- 17 -
REF
/2)+0.175
/2)+0.175
Min
SEH
, the single-ended components of differential signals have a requirement
IL
REFCA
min has no bearing on timing, but adds a restriction on the common
DDR3-800/1066/1333/1600
(AC) ) for DQ signals) in every half-cycle proceeding and following a
; if a reduced ac-high or ac-low level is used for a signal group, then the
IH
V
IH
(AC) / V
SEL
150(AC)/V
(V
(V
DD
DD
NOTE 3
NOTE 3
IL
IH
Max
/2)-0.175
/2)-0.175
(AC) ) for ADD/CMD signals) in every
(DC) max, V
CK or DQS
IL
150(AC) is used for ADD/CMD
DDR3L SDRAM
time
IL
(DC)min) for single-ended sig-
Unit
V
V
V
V
Rev. 1.0
NOTE
1, 2
1, 2
1, 2
1, 2