ST92T163R4T1 STMicroelectronics, ST92T163R4T1 Datasheet - Page 132

• Manufacturer Part Number: ST92T163R4T1
• Description: Microcontrollers (MCU) OTP EPROM 20K USB/I2
• Manufacturer: STMicroelectronics

Specifications of ST92T163R4T1

• Data Bus Width: 8 bit, 16 bit
• Program Memory Type: EPROM
• Program Memory Size: 20 KB
• Data Ram Size: 2 KB
• Interface Type: I2C, SCI, USB
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 64
• Number Of Timers: 2
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Package / Case: TQFP-64
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8 bit
• Lead Free Status / Rohs Status: No

ST92163 - MULTIFUNCTION TIMER (MFT)
MULTIFUNCTION TIMER (Cont’d)
INTERRUPT/DMA MASK REGISTER (IDMR)
R255 - Read/Write
Register Page: 10
Reset value: 0000 0000 (00h)
Bit 7 = GTIEN: Global timer interrupt enable .
This bit is set and cleared by software.
0: Disable all Timer interrupts
1: Enable all timer Timer Interrupts from enabled
Bit 6 = CP0D: Capture 0 DMA mask.
This bit is set by software to enable a Capt0 DMA
transfer and cleared by hardware at the end of the
block transfer.
0: Disable capture on REG0R DMA
1: Enable capture on REG0R DMA
Bit 5 = CP0I: Capture 0 interrupt mask .
0: Disable capture on REG0R interrupt
1: Enable capture on REG0R interrupt (or Capt0
Bit 4 = CP1I: Capture 1 interrupt mask .
This bit is set and cleared by software.
0: Disable capture on REG1R interrupt
1: Enable capture on REG1R interrupt
Bit 3 = CM0D: Compare 0 DMA mask.
This bit is set by software to enable a Comp0 DMA
transfer and cleared by hardware at the end of the
block transfer.
0: Disable compare on CMP0R DMA
1: Enable compare on CMP0R DMA
Bit 2 = CM0I: Compare 0 Interrupt mask .
This bit is set and cleared by software.
0: Disable compare on CMP0R interrupt
1: Enable compare on CMP0R interrupt (or
132/224
GT-
IEN
sources
DMA End of Block interrupt if CP0D=1)
Comp0 DMA End of Block interrupt if CM0D=1)
7
CP0D CP0I
CP1I
CM0
D
CM0I CM1I OUI
0
Bit 1 = CM1I: Compare 1 Interrupt mask .
This bit is set and cleared by software.
0: Disable compare on CMP1R interrupt
1: Enable compare on CMP1R interrupt
Bit 0 = OUI:
Overflow/Underflow interrupt mask .
This bit is set and cleared by software.
0: Disable Overflow/Underflow interrupt
1: Enable Overflow/Underflow interrupt
DMA COUNTER POINTER REGISTER (DCPR)
R240 - Read/Write
Register Page: 9
Reset value: undefined
Bit 7:2 = DCP[7:2]: MSBs of DMA counter register
address.
These are the most significant bits of the DMA
counter register address programmable by soft-
ware. The DCP2 bit may also be toggled by hard-
ware if the Timer DMA section for the Compare 0
channel is configured in Swap mode.
Bit 1 = DMA-SRCE: DMA source selection.
This bit is set and cleared by hardware.
0: DMA source is a Capture on REG0R register
1: DMA destination is a Compare on CMP0R reg-
Bit 0 = REG/MEM: DMA area selection .
This bit is set and cleared by software. It selects
the source and destination of the DMA area
0: DMA from/to memory
1: DMA from/to Register File
DCP7 DCP6 DCP5 DCP4 DCP3 DCP2
ister
7
SRCE
DMA
REG/
MEM
0