STV0299B STMicroelectronics, STV0299B Datasheet - Page 12

• Manufacturer Part Number: STV0299B
• Manufacturer: STMicroelectronics

Specifications of STV0299B

• Pin Count: 64
• Screening Level: Commercial
• Lead Free Status / Rohs Status: Specific Sites Compliant

STV0299B
4
4.2 Signal Processing
4.2.1
The ADC features differential inputs, but in most
applications I & Q signals are single-ended. In
such applications, I and Q signals from the tuner
are fed to the respective IP and QP inputs through
a capacitor. The I
typically to V
done on the circuit at the mid-voltage between
V
The
described in Address 0Ch.
4.2.2
The modulus of the I/Q input is compared to a
programmable threshold, m1, and the difference
is integrated. This signal is then converted into a
pulse density modulation signal to drive the AGC
output. It should be filtered by a simple analog
filter to control the gain command of any amplifier
before the A to D converter.
The output converter operates at f
to decrease the radiated noise and to simplify the
filter design. The output is a 5 V tolerant open
drain stage.
The reset value of the coefficient allows an initial
settling time of less than 100k master clock
periods.
The 8 integrator MSBs may be read or written at
any time by the microprocessor. When written, the
LSB’s are reset and the coefficient may be set to
zero by programming (in this case, the AGC is
reduced
synthesizer).
The time constant of agc1 is estimated as
followed:
with m1 = AGC1 reference level.
The AGC1 Control, AGC1 Reference and AGC1
Integrator Registers are in Addresses 0D and 0F.
4.2.3
Two roll off values are available: 0.35 and 0.20.
Refer to the Input/Output Configuration Register
in Address 0C.
4.2.4
This
component on I and Q. The compensation may be
frozen to its last value by resetting the DC offset
12/36
TOP
FUNCTIONAL DESCRIPTION (continued)
and V
Input/Output
device
I and Q Inputs
Main AGC (or AGC1)
Nyquist Root and Interpolation Filters
Offset Cancellation
to
BOT
BOT
T
.
agc1
a
.The internal biasing of the ADC is
suppresses
N
programmable
=
and Q
2
-----------------------
Configuration
26
m1
–
a gc1
N
pins are DC biased,
the
T
M_CLK
M_CLK
8-bit
residual
Register
/8 in order
voltage
DC
is
compensation bit in the AGC Control Register in
Address 0D.
4.2.5
The rms value of I and Q is measured after the
Nyquist filter and compared to a programmable
value, m2, such as that of the main AGC.
The integrated error signal is applied to a
multiplier on each I and Q path.
The AGC2 Control Register is in Address 10.
Bits [7:5] give the AGC2 coefficient, which sets
beta_agc2, the gain of the integrator. Table 4
shows how beta_agc2 is programmed with AGC2
coefficient (which is related to the time constant of
the AGC).
Table 4:
If
unchanged from its last value.
The time constant is independent of the symbol
frequency, however it does depend on the
modulus, m1, of the input signal, programmed in
AGC1, with the following approximate relation:
The AGC2 Integrator Registers (2 bytes - MSB
and LSB) are in Addresses 18 and 19. These
values
microprocessor. When written, all the LSB’s
integrator bits are reset. This value is an image of
the signal power in the useful band. Compared
with the total power of the signal, the out-of-band
power may be computed (noise, or other channel).
AGC2
AGC2 Coefficient
Signal AGC (or AGC2)
may
0
1
2
3
4
5
6
7
Coefficient = 0,
T
agc2
be
=
read
60
-------------------------------------------- -
m1 beta_agc2
10
3
or
the
T
M_CLK
beta_agc2
written
gain
256
N/A
N/A
16
64
0
1
4
remains
by
the