AT32UC3A3128 Atmel Corporation, AT32UC3A3128 Datasheet - Page 641

• Manufacturer Part Number: AT32UC3A3128
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A3128

• Flash (kbytes): 128 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32072G–11/2011
RXOUTI
FIFOCON
RXOUTI
FIFOCON
OUT
OUT
•Detailed description
(bank 0)
(bank 0)
DATA
DATA
Figure 26-19. Example of an OUT Endpoint with one Data Bank
Figure 26-20. Example of an OUT Endpoint with two Data Banks
The data is read, following the next flow:
If the endpoint uses several banks, the current one can be read while the following one is being
written by the host. Then, when the user clears FIFOCON, the following bank may already be
ready and RXOUTI is set immediately.
In Hi-Speed mode, the PING and NYET protocol is handled by the USBB. For single bank, a
NYET handshake is always sent to the host (on Bulk-out transaction) to indicate that the current
packet is acknowledged but there is no room for the next one. For double bank, the USBB
• When the bank is full, RXOUTI and FIFOCON are set, what triggers an EPnINT interrupt if
• The user acknowledges the interrupt by writing a one to RXOUTIC in order to clear RXOUTI.
• The user can read the byte count of the current bank from BYCT to know how many bytes to
• The user reads the data from the current bank by using the USBFIFOnDATA register (see
• The user frees the bank and switches to the next bank (if any) by clearing FIFOCON.
RXOUTE is one.
read, rather than polling RWALL.
”USB Pipe/Endpoint n FIFO Data Register (USBFIFOnDATA)” on page
expected data frame is read or the bank is empty (in which case RWALL is cleared and
BYCT reaches zero).
HW
ACK
ACK
HW
SW
read data from CPU
SW
BANK 0
OUT
NAK
read data from CPU
BANK 0
(bank 1)
DATA
SW
OUT
ACK
(bank 0)
DATA
HW
SW
HW
ACK
740), until all the
read data from CPU
read data from CPU
SW
SW
BANK 1
BANK 0
641