SAM3N4B Atmel Corporation, SAM3N4B Datasheet - Page 672

• Manufacturer Part Number: SAM3N4B
• Manufacturer: Atmel Corporation

Specifications of SAM3N4B

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 48 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Quadrature Decoder Channels: 2
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 10
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 24
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

33.7.12
Name:
Address:
Access:
• EOCx: End of Conversion x
0 = Corresponding analog channel is disabled, or the conversion is not finished. This flag is cleared when reading the cor-
responding ADC_CDRx registers.
1 = Corresponding analog channel is enabled and conversion is complete.
• DRDY: Data Ready
0 = No data has been converted since the last read of ADC_LCDR.
1 = At least one data has been converted and is available in ADC_LCDR.
• GOVRE: General Overrun Error
0 = No General Overrun Error occurred since the last read of ADC_ISR.
1 = At least one General Overrun Error has occurred since the last read of ADC_ISR.
• COMPE: Comparison Error
0 = No Comparison Error since the last read of ADC_ISR.
1 = At least one Comparison Error has occurred since the last read of ADC_ISR.
• ENDRX: End of RX Buffer
0 = The Receive Counter Register has not reached 0 since the last write in ADC_RCR or ADC_RNCR.
1 = The Receive Counter Register has reached 0 since the last write in ADC_RCR or ADC_RNCR.
• RXBUFF: RX Buffer Full
0 = ADC_RCR or ADC_RNCR have a value other than 0.
1 = Both ADC_RCR and ADC_RNCR have a value of 0.
672
672
EOC15
EOC7
31
23
15
–
–
7
SAM3N
SAM3N
ADC Interrupt Status Register
EOC14
EOC6
30
22
14
ADC_ISR
0x40038030
Read-only
–
–
6
EOC13
EOC5
29
21
13
–
–
5
RXBUFF
EOC12
EOC4
28
20
12
–
4
ENDRX
EOC11
EOC3
27
19
11
–
3
COMPE
EOC10
EOC2
26
18
10
–
2
GOVRE
EOC9
EOC1
25
17
–
9
1
11011A–ATARM–04-Oct-10
11011A–ATARM–04-Oct-10
DRDY
EOC8
EOC0
24
16
–
8
0