AT32UC3C2512C Automotive Atmel Corporation, AT32UC3C2512C Automotive Datasheet - Page 1296
AT32UC3C2512C Automotive
Manufacturer Part Number
AT32UC3C2512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 1296 of 1312
- Download datasheet (20Mb)
43.2
43.2.1
43.2.2
43.2.3
43.2.4
9166C–AVR-08/11
rev D
AST
aWire
GPIO
Power Manager
1
1
1
1
2
3
AST wake signal is released one AST clock cycle after the BUSY bit is cleared
After writing to the Status Clear Register (SCR) the wake signal is released one AST clock
cycle after the BUSY bit in the Status Register (SR.BUSY) is cleared. If entering sleep mode
directly after the BUSY bit is cleared the part will wake up immediately.
Fix/Workaround
Read the Wake Enable Register (WER) and write this value back to the same register. Wait
for BUSY to clear before entering sleep mode.
aWire MEMORY_SPEED_REQUEST command does not return correct CV
The aWire MEMORY_SPEED_REQUEST command does not return a CV corresponding to
the formula in the aWire Debug Interface chapter.
Fix/Workaround
I s s u e a d u m m y r e a d t o a d d r e s s 0 x 1 0 0 0 0 0 0 0 0 b e f o r e i s s u i n g t h e
MEMORY_SPEED_REQUEST command and use this formula instead:
Clearing Interrupt flags can mask other interrupts
When clearing interrupt flags in a GPIO port, interrupts on other pins of that port, happening
in the same clock cycle will not be registered.
Fix/Workaround
Read the PVR register of the port before and after clearing the interrupt to see if any pin
change has happened while clearing the interrupt. If any change occurred in the PVR
between the reads, they must be treated as an interrupt.
Clock Failure Detector (CFD) can be issued while turning off the CFD
While turning off the CFD, the CFD bit in the Status Register (SR) can be set. This will
change the main clock source to RCSYS.
Fix/Workaround
Solution 1: Enable CFD interrupt. If CFD interrupt is issues after turning off the CFD, switch
back to original main clock source.
Solution 2: Only turn off the CFD while running the main clock on RCSYS.
Requesting clocks in idle sleep modes will mask all other PB clocks than the
requested
In idle or frozen sleep mode, all the PB clocks will be frozen if the TWIS or the AST need to
wake the cpu up.
Fix/Workaround
Disable the TWIS or the AST before entering idle or frozen sleep mode.
TWIS may not wake the device from sleep mode
f
sab
=
---------------- -
CV 3
7f
aw
–
AT32UC3C
1296
Related parts for AT32UC3C2512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: