AT32UC3C2512C Automotive Atmel Corporation, AT32UC3C2512C Automotive Datasheet - Page 740
AT32UC3C2512C Automotive
Manufacturer Part Number
AT32UC3C2512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 740 of 1312
- Download datasheet (20Mb)
28.8.6.1
28.8.6.2
28.8.7
28.8.7.1
9166C–AVR-08/11
SMBus Mode
Data Transmit with the Peripheral DMA Controller
Packet Error Checking (PEC)
Data Receive with the Peripheral DMA Controller
To assure correct behavior, respect the following programming sequences:
SMBus mode is enabled by writing a one to the SMBus Mode Enable (SMEN) bit in CR. SMBus
mode operation is similar to I²C operation with the following exceptions:
Each SMBus transfer can optionally end with a CRC byte, called the PEC byte. Writing a one to
the Packet Error Checking Enable (PECEN) bit in CR enables automatic PEC handling in the
current transfer. The PEC generator is always updated on every bit transmitted or received, so
that PEC handling on following linked transfers will be correct.
In slave receiver mode, the master calculates a PEC value and transmits it to the slave after all
data bytes have been transmitted. Upon reception of this PEC byte, the slave will compare it to
the PEC value it has computed itself. If the values match, the data was received correctly, and
the slave will return an ACK to the master. If the PEC values differ, data was corrupted, and the
slave will return a NAK value. The SR.SMBPECERR bit is set automatically if a PEC error
occurred.
In slave transmitter mode, the slave calculates a PEC value and transmits it to the master after
all data bytes have been transmitted. Upon reception of this PEC byte, the master will compare
it to the PEC value it has computed itself. If the values match, the data was received correctly. If
the PEC values differ, data was corrupted, and the master must take appropriate action.
The PEC byte is automatically inserted in a slave transmitter transmission if PEC enabled when
NBYTES reaches zero. The PEC byte is identified in a slave receiver transmission if PEC
1. Initialize the transmit Peripheral DMA Controller (memory pointers, size, etc.).
2. Configure the TWIS (ADR, NBYTES, etc.).
3. Start the transfer by enabling the Peripheral DMA Controller to transmit.
4. Wait for the Peripheral DMA Controller end-of-transmit flag.
5. Disable the Peripheral DMA Controller.
1. Initialize the receive Peripheral DMA Controller (memory pointers, size - 1, etc.).
2. Configure the TWIS (ADR, NBYTES, etc.).
3. Start the transfer by enabling the Peripheral DMA Controller to receive.
4. Wait for the Peripheral DMA Controller end-of-receive flag.
5. Disable the Peripheral DMA Controller.
• Only 7-bit addressing can be used.
• The SMBus standard describes a set of timeout values to ensure progress and throughput on
• Transmissions can optionally include a CRC byte, called Packet Error Check (PEC).
• A dedicated bus line, SMBALERT, allows a slave to get a master’s attention.
• A set of addresses have been reserved for protocol handling, such as Alert Response
the bus. These timeout values must be written to TR.
Address (ARA) and Host Header (HH) Address. Address matching on these addresses can
be enabled by configuring CR appropriately.
AT32UC3C
740
Related parts for AT32UC3C2512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: