ADUC847 Analog Devices, ADUC847 Datasheet - Page 29

• Manufacturer Part Number: ADUC847
• Description: Precision Analog Microcontroller: 12MIPS 8052 Flash MCU + 10-Ch 24-Bit ADC + 12-Bit DAC
• Manufacturer: Analog Devices

Specifications of ADUC847

• Mcu Core: 8052
• Mcu Speed (mips): 12
• Sram (bytes): 2304Bytes
• Gpio Pins: 34
• Adc # Channels: 10
• Other: PWM

ADC Noise Performance with Chop Enabled (CHOP = 0)
Table 10, Table 11, Table 12, and Table 13 show the output rm
noise and output peak-to-peak resolution in bits (rounded to
the nearest 0.5 LSB) for some typical output update rates for th
ADuC845, ADuC847, and ADuC848. The numbers are typica
and are generated at a differential input voltage of 0 V and a
common-mode voltage of 2.5 V. The output update rate is
selected via the SF7 to SF0 bits in the SF filter register. It is
important to note that the peak-to-peak resolution figures
represent the resolution for which there is no code flicker
within a 6-sigma limit.
The outp
the electrical noise in the semic
Table 10. ADuC845 and ADuC847 Typical Output RMS Noise (µV) vs. Input Range and Update Rate with Chop Enabled
SF Word
13
23
27
69
255
Table 11. ADuC845 and ADuC847 Typical Peak-to-Peak Resolution (Bits) vs. Input Range and Update Rate with Chop Enabled
SF Word
13
23
27
69
255
Table 12. ADuC848 Typical Output Noise (µV) vs. Input Range and Update Rate with Chop Enabled
SF Word
13
23
27
69
255
Table 13. ADuC848 Typical Peak-to-Peak Resolution (Bits) vs. Input Range and Update Rate with Chop Enabled
SF Word
13
23
27
69
255
ut noise comes from two sources. The first source is
Data Update Rate (Hz)
105.03
59.36
50.56
19.79
5.35
Data Update Rate (Hz)
105.03
59.36
50.56
19.79
5.35
Data Update Rate (Hz)
105.03
59.36
50.56
19.79
5.35
Data Update Rate (Hz)
105.03
59.36
50.56
19.79
5.35
ond
uctor devices (device noise)
±20 mV
±20 mV
±20 mV
±20 mV
1.75
1.25
1.0
0.63
0.31
12
12
12.5
13
14.5
1.75
1.25
1.0
0.63
0.31
12
12
12.5
13
14.5
±40 mV
1.30
0.95
1.0
0.68
0.38
±40 mV
13
13.5
13.5
14
15
±40 mV
1.30
0.95
1.0
0.68
0.38
±40 mV
13
13.5
13.5
14
15
Rev. B | Page 29 of 108
s
l
e
±80 mV
1.65
1.08
0.85
0.52
0.34
±80 mV
14
14.5
15
15.5
16
±80 mV
1.65
1.08
0.85
0.52
0.34
±80 mV
14
14.5
15
15.5
16
used in the implementation of the modulator. The second
source is quantization noise, which is added when the analog
input is converted to the digital domain. The device noise is at a
low level and is independent of frequency. The quantization
noise starts at an even lower level but rises rapidly with increasing
frequency to become the dominant noise source.
The numbers in the tables are given for the bipolar input ran
For the unipolar ran
range as the bipolar figures, but the peak-to-peak resolution is
based on half the signal range, which effectively means losing
1 bit of resolution.
±160 mV
1.5
0.94
0.85
0.7
0.32
±160 mV
15
15.5
16
16
17
±160 mV
1.5
0.94
0.85
0.7
0.32
±160 mV
15
15.5
16
16
16
Input Range
Input Range
Input Range
Input Range
±320 m
2.1
1.0
1.13
0.61
0.4
±320 mV
15.5
16.5
16.5
17.5
18
±320 mV
2.1
1.0
1.13
0.61
0.4
±320 mV
15.5
16
16
16
16
ADuC845/ADuC847/ADuC848
ges, the rms noise numbers are in the same
V
±640 mV
3.1
1.87
1.56
1.1
0.45
±640 mV
16
16.5
17
17.5
18.5
±640 mV
3.1
1.87
1.56
1.1
0.45
±640 mV
16
16
16
16
16
±1.28 V
7.15
3.24
2.9
1.3
0.68
±1.28 V
16
17
17
18
19
±1.28 V
7.15
3.24
2.9
1.3
0.68
±1.28 V
16
17
16
16
16
±2.56 V
13.3
7.1
3.6
2.75
1.22
±2.56 V
16
16.5
17.5
18
19.5
±2.56 V
13.3
7.1
3.6
2.75
1.22
±2.56 V
16
16
16
16
16
ges.