lan9311 Standard Microsystems Corp., lan9311 Datasheet - Page 32

no-image

lan9311

Manufacturer Part Number
lan9311
Description
Lan9311/lan9311i Two Port 10/100 Managed Ethernet Switch With 16-bit Non-pci Cpu Interface
Manufacturer
Standard Microsystems Corp.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lan9311-NU
Manufacturer:
CINCERA
Quantity:
3 023
Part Number:
lan9311-NU
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
lan9311-NU
Manufacturer:
SMSC
Quantity:
20 000
Part Number:
lan9311-NZW
Manufacturer:
Standard
Quantity:
2
Part Number:
lan9311-NZW
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
lan9311I-NZW
Manufacturer:
Standard
Quantity:
836
Part Number:
lan9311I-NZW
Manufacturer:
Microchip Technology
Quantity:
10 000
Revision 1.2 (04-08-08)
PIN
101
PIN
67
68
Note 3.3
Note 3.4
Note 3.5
PHY Address
Size Strap 0
LED Enable
Chip Select
EEPROM
EEPROM
Microwire
NAME
NAME
Strap
Strap
The IS buffer type is valid only during the time specified in
Configuration Strap Timing," on page
Configuration strap values are latched on power-on reset or nRST de-assertion.
Configuration strap pins are identified by an underlined symbol name. Refer to
4.2.4, "Configuration Straps," on page 40
The IS buffer type is valid only during the time specified in
Configuration Strap Timing," on page 447
EEPROM_SIZE_0
Table 3.6 Dedicated Configuration Strap Pins
PHY_ADDR_SEL
SYMBOL
SYMBOL
LED_EN
EECS
Table 3.5 EEPROM Pins (continued)
DATASHEET
BUFFER
BUFFER
Note 3.3
TYPE
TYPE
(PU)
(PU)
O8
IS
IS
IS
32
Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
EEPROM Microwire Chip Select: In Microwire
EEPROM mode (EEPROM_TYPE = 0), this pin is
the Microwire EEPROM chip select output.
Note:
EEPROM Size Strap 0: Configures the low bit of
the EEPROM size range as specified in
10.2, "I2C/Microwire Master EEPROM Controller,"
on page
LED Enable Strap: Configures the default value
for the LED_EN bits in the
Register
LED/GPIO pins are configured as GPIOs. When
latched high, all 8 LED/GPIO pins are configured
as LEDs. See
PHY Address Select Strap: Configures the default
MII management address values for the PHYs
(Virtual, Port 1, and Port 2) as detailed in
7.1.1, "PHY Addressing," on page
See
447.
0
1
for more information.
and when in I
Note
138. See
In I
is not used and is driven low.
(LED_CFG). When latched low, all 8
3.6.
0
1
2
C mode (EEPROM_TYPE=1), this pin
Note
DESCRIPTION
DESCRIPTION
2
Note
1
2
C mode.
3.6.
3.4.
Section 15.5.2, "Reset and
Section 15.5.2, "Reset and
2
3
LED Configuration
SMSC LAN9311/LAN9311i
82.
Section
Section
Datasheet
Section

Related parts for lan9311