AD9992_07 AD [Analog Devices], AD9992_07 Datasheet - Page 31

• Manufacturer Part Number: AD9992_07
• Description: 12-Bit CCD Signal Processor with Precision Timing Generator
• Manufacturer: AD [Analog Devices]

Register
VREPA_3
VREPA_4
VREPB_ODD
VREPC_ODD
VREPD_ODD
VREPB_EVEN
VREPC_EVEN
VREPD_EVEN
FREEZE1
FREEZE2
FREEZE3
FREEZE4
RESUME1
RESUME2
RESUME3
RESUME4
LASTREPLEN_A
LASTREPLEN_B
LASTREPLEN_C
LASTREPLEN_D
LASTTOG_A
LASTTOG_B
LASTTOG_C
LASTTOG_D
VSEQALT_EN
VALT_MAP
VALTSEL0_EVEN
VALTSEL1_EVEN
VALTSEL0_ODD
VALTSEL1_ODD
SPC_PAT_EN
Length
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
13b
1b
1b
18b
18b
18b
18b
1b
Description
Number of repetitions for the V-Pattern Group A for third lines.
Number of repetitions for the V-Pattern Group A for fourth lines.
Number of repetitions for the V-Pattern Group B for odd lines.
Number of repetitions for the V-Pattern Group C for odd lines.
Number of repetitions for the V-Pattern Group D for odd lines.
Number of repetitions for the V-Pattern Group B for even lines.
Number of repetitions for the V-Pattern Group C for even lines.
Number of repetitions for the V-Pattern Group D for even lines.
Pixel location where the V-outputs freeze or hold (see VMASK_EN). Also used as VALTSEL0_EVEN [12:0] register
when special VSEQALT_EN mode is enabled.
Pixel location where the V-outputs freeze or hold (see VMASK_EN). Also used as VALTSEL1_EVEN [12:0] register
when special VSEQALT_EN mode is enabled.
Pixel location where the V-outputs freeze or hold (see VMASK_EN). Also used as VALTSEL0_ODD [12:0] register
when special VSEQALT_EN mode is enabled.
Pixel location where the V-outputs freeze or hold (see VMASK_EN). Also used as VALTSEL1_ODD [12:0] register
when special VSEQALT_EN mode is enabled.
Pixel location where the V-outputs resume operation (see VMASK_EN). Also used as VALTSEL0_EVEN [17:13]
register when S within line for each XV1 to XV24 output when special VSEQALT_EN mode is enabled.
Pixel location where the V-outputs resume operation (see VMASK_EN). Also used as VALTSEL1_EVEN [17:13]
register when special VSEQALT_EN mode is enabled.
Pixel location where the V-outputs resume operation (see VMASK_EN). Also used as VALTSEL0_ODD [17:13]
register when special VSEQALT_EN mode is enabled.
Pixel location where the V-outputs resume operation (see VMASK_EN). Also used as VALTSEL1_ODD [17:13]
register when special VSEQALT_EN mode is enabled.
Separate length for last repetition of vertical pulses. Must be enabled using LASTREPLEN_EN.
Should be programmed to a value equal to the VLENA register.
Separate length for last repetition of vertical pulses. Must be enabled using LASTREPLEN_EN.
Should be programmed to a value equal to the VLENB register.
Separate length for last repetition of vertical pulses. Must be enabled using LASTREPLEN_EN.
Should be programmed to a value equal to the VLENC register.
Separate length for last repetition of vertical pulses. Must be enabled using LASTREPLEN_EN.
Should be programmed to a value equal to the VLEND register.
Optional fifth toggle position for the vertical signals. Must be enabled using LASTTOG_EN.
Note that the toggle position is common for all vertical signals.
Optional fifth toggle position for the vertical signals. Must be enabled using LASTTOG_EN.
Note that the toggle position is common for all vertical signals.
Optional fifth toggle position for the vertical signals. Must be enabled using LASTTOG_EN.
Note that the toggle position is common for all vertical signals.
Optional fifth toggle position for the vertical signals. Must be enabled using LASTTOG_EN.
Note that the toggle position is common for all vertical signals.
Special V-sequence alternation mode is enabled when this register is programmed high.
Enables the use of FREEZE/RESUME register locations to specify the VALTSEL0 and VALTSEL1 registers. Must be
enabled if VSEQALT mode is enabled.
Select lines for special V-sequence alternation mode for even lines. Used to concatenate VPAT Groups A/B/C/D into
unique merged patterns. Setting is used to specify one segment, with up to a maximum of 18 segments.
Select lines for special V-sequence alternation mode for even lines. Used to concatenate VPAT Groups A/B/C/D into
unique merged patterns. Setting is used to specify one segment, with up to a maximum of 18 segments.
Select lines for special V-sequence alternation mode for odd lines. Used to concatenate VPAT Groups A/B/C/D into
unique merged patterns. Setting is used to specify one segment, with up to a maximum of 18 segments.
Select lines for special V-sequence alternation mode for odd lines. Used to concatenate VPAT Groups A/B/C/D into
unique merged patterns. Setting is used to specify one segment, with up to a maximum of 18 segments.
Enable special V-pattern to be inserted into one repetition of a VPATA series.
SPC_PAT_EN [0]: Set to 1 to enable VPATB to be used as special pattern insertion.
SPC_PAT_EN [1]: Set to 1 to enable VPATC to be used as special pattern insertion.
SPC_PAT_EN [2]: Set to 1 to enable VPATD to be used as special pattern insertion.
Rev. C | Page 31 of 92
AD9992