S9S12P96J0VFTR Freescale Semiconductor, S9S12P96J0VFTR Datasheet - Page 373

no-image

S9S12P96J0VFTR

Manufacturer Part Number
S9S12P96J0VFTR
Description
16-bit Microcontrollers - MCU 16 BIT 96K FLASH
Manufacturer
Freescale Semiconductor
Datasheet

Specifications of S9S12P96J0VFTR

Rohs
yes
Core
S12
Processor Series
MC9S12P
Data Bus Width
16 bit
Maximum Clock Frequency
16 MHz
Program Memory Size
96 KB
Data Ram Size
6 KB
On-chip Adc
Yes
Operating Supply Voltage
3.15 V to 5.5 V
Operating Temperature Range
- 40 C to + 105 C
11.3.2.7
The SCISR1 and SCISR2 registers provides inputs to the MCU for generation of SCI interrupts. Also,
these registers can be polled by the MCU to check the status of these bits. The flag-clearing procedures
require that the status register be read followed by a read or write to the SCI data register.It is permissible
to execute other instructions between the two steps as long as it does not compromise the handling of I/O,
but the order of operations is important for flag clearing.
Read: Anytime
Write: Has no meaning or effect
Freescale Semiconductor
Module Base + 0x0004
Reset
TDRE
RDRF
Field
IDLE
TC
7
6
5
4
W
R
TDRE
Transmit Data Register Empty Flag — TDRE is set when the transmit shift register receives a byte from the
SCI data register. When TDRE is 1, the transmit data register (SCIDRH/L) is empty and can receive a new value
to transmit.Clear TDRE by reading SCI status register 1 (SCISR1), with TDRE set and then writing to SCI data
register low (SCIDRL).
0 No byte transferred to transmit shift register
1 Byte transferred to transmit shift register; transmit data register empty
Transmit Complete Flag — TC is set low when there is a transmission in progress or when a preamble or break
character is loaded. TC is set high when the TDRE flag is set and no data, preamble, or break character is being
transmitted.When TC is set, the TXD pin becomes idle (logic 1). Clear TC by reading SCI status register 1
(SCISR1) with TC set and then writing to SCI data register low (SCIDRL). TC is cleared automatically when data,
preamble, or break is queued and ready to be sent. TC is cleared in the event of a simultaneous set and clear of
the TC flag (transmission not complete).
0 Transmission in progress
1 No transmission in progress
Receive Data Register Full Flag — RDRF is set when the data in the receive shift register transfers to the SCI
data register. Clear RDRF by reading SCI status register 1 (SCISR1) with RDRF set and then reading SCI data
register low (SCIDRL).
0 Data not available in SCI data register
1 Received data available in SCI data register
Idle Line Flag — IDLE is set when 10 consecutive logic 1s (if M = 0) or 11 consecutive logic 1s (if M =1) appear
on the receiver input. Once the IDLE flag is cleared, a valid frame must again set the RDRF flag before an idle
condition can set the IDLE flag.Clear IDLE by reading SCI status register 1 (SCISR1) with IDLE set and then
reading SCI data register low (SCIDRL).
0 Receiver input is either active now or has never become active since the IDLE flag was last cleared
1 Receiver input has become idle
Note: When the receiver wakeup bit (RWU) is set, an idle line condition does not set the IDLE flag.
SCI Status Register 1 (SCISR1)
1
7
= Unimplemented or Reserved
TC
1
6
Figure 11-10. SCI Status Register 1 (SCISR1)
Table 11-11. SCISR1 Field Descriptions
S12P-Family Reference Manual, Rev. 1.13
RDRF
0
5
IDLE
0
4
Description
OR
0
3
Serial Communication Interface (S12SCIV5)
NF
0
2
FE
0
1
PF
0
0
373

Related parts for S9S12P96J0VFTR