ADP5585CP-EVALZ Analog Devices, ADP5585CP-EVALZ Datasheet - Page 30

no-image

ADP5585CP-EVALZ

Manufacturer Part Number
ADP5585CP-EVALZ
Description
Interface Development Tools LFCSP Evaluation Board
Manufacturer
Analog Devices
Series
ADP5585r
Datasheet

Specifications of ADP5585CP-EVALZ

Rohs
yes
Product
Evaluation Boards
Tool Is For Evaluation Of
ADP5585
Interface Type
I2C
Operating Supply Voltage
1.8 V to 3 V
Factory Pack Quantity
1
ADP5585
GPIO_DIRECTION_A Register 0x27
Table 47. GPIO_DIRECTION_A Bit Descriptions
Bit(s)
7 to 6
5
4
3
2
1
0
GPIO_DIRECTION_B Register 0x28
Table 48. Register 0x28, GPIO_DIRECTION_B Bit Descriptions
Bit(s)
7 to 5
4
3
2
1
0
RESET1_EVENT_A Register 0x29
Table 49. RESET1_EVENT_A Bit Descriptions
Bit(s)
7
6 to 0
Bit Name
RESET1_EVENT_A_LEVEL
RESET1_EVENT_A[6:0]
Bit Name
N/A
GPIO_11_DIR
GPIO_10_DIR
GPIO_9_DIR
GPIO_8_DIR
GPIO_7_DIR
N/A
GPIO_2_DIR
Bit Name
GPIO_6_DIR
GPIO_5_DIR
GPIO_4_DIR
GPIO_3_DIR
GPIO_1_DIR
Access
Read/write
Read/write
Read/write
Read/write
Read/write
Read/write
Access
Read/write
Read/write
Read/write
Read/write
Read/write
Access
Read/write
Read/write
Rev. C | Page 30 of 40
Description
Reserved.
(Reserved except for ADP5585AC_Z-01-R7 options)
0 = GPIO 6 is an input.
1 = GPIO 6 is an output.
0 = GPIO 5 is an input.
1 = GPIO 5 is an output.
0 = GPIO 4 is an input.
1 = GPIO 4 is an output.
0 = GPIO 3 is an input.
1 = GPIO 3 is an output.
0 = GPIO 2 is an input.
1 = GPIO 2 is an output.
0 = GPIO 1 is an input.
1 = GPIO 1 is an output.
Description
Reserved.
0 = GPIO 11 is an input.
1 = GPIO 11 is an output.
0 = GPIO 10 is an input.
1 = GPIO 10 is an output.
0 = GPIO 9 is an input.
1 = GPIO 9 is an output.
0 = GPIO 8 is an input.
1 = GPIO 8 is an output.
0 = GPIO 7 is an input.
1 = GPIO 7 is an output.
Description
Defines which level the first reset event should be to generate the
RESET1 signal.
For key events, use the following settings:
0 = not applicable; releases not used for reset generation.
1 = press is used as reset event.
For GPIs and logic outputs configured for FIFO updates, use the
following settings:
0 = inactive event used as reset condition.
1 = active event used as reset condition.
Defines an event that can be used to generate the RESET1 signal. Up to
three events can be defined for generating the RESET1 signal, using
RESET1_EVENT_A[6:0], RESET1_EVENT_B[6:0], and
RESET1_EVENT_C[6:0]. If one of the registers is 0, that register is not
used for reset generation. All reset events must be detected at the
same time to trigger the reset.
Data Sheet

Related parts for ADP5585CP-EVALZ