AT45DB161D-SU Atmel, AT45DB161D-SU Datasheet - Page 2

• Manufacturer Part Number: AT45DB161D-SU
• Description: IC FLASH 16MBIT 66MHZ 8SOIC
• Manufacturer: Atmel

Specifications of AT45DB161D-SU

• Format - Memory: FLASH
• Memory Type: DataFLASH
• Memory Size: 16M (4096 pages x 528 bytes)
• Speed: 66MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Architecture: Sectored
• Interface Type: SPI
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Maximum Operating Current: 15 mA
• Mounting Style: SMD/SMT
• Organization: 128 KB x 16
• Current, Input, Leakage: 1 μA
• Current, Operating: 11 mA (Read), 12 mA (Program/Erase)
• Current, Output, Leakage: 1
• Data Retention: 20 yrs.
• Density: 16M
• Package Type: EIAJ SOIC
• Temperature, Operating: -40 to +85 °C
• Time, Access: 6 ns
• Time, Address Hold: 5
• Time, Address Setup: 5
• Time, Fall: 6.8 ns
• Time, Rise: 6.8 ns
• Voltage, Input, High: 1.89 to 2.52 V
• Voltage, Input, Low: 0.81 to 1.08 V
• Voltage, Output, High: 2.5 V
• Voltage, Output, Low: 0.4 V
• Voltage, Supply: 2.7 to 3.6 V
• Memory Configuration: 4096 Pages X 528 Bytes
• Clock Frequency: 66MHz
• Supply Voltage Range: 2.5V To 3.6V, 2.7V To 3.6V
• Rohs Compliant: Yes
• Access Time (max): 6ns
• Boot Type: Not Required
• Address Bus: 1b
• Operating Supply Voltage (typ): 3/3.3V
• Operating Temp Range: -40C to 85C
• Program/erase Volt (typ): 2.7 to 3.6V
• Sync/async: Synchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Supply Current: 15mA
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2.
Note:
2
Figure 2-1.
Figure 2-3.
RDY/BUSY
RESET
operation. Unlike conventional Flash memories that are accessed randomly with multiple address lines and a
parallel interface, the Atmel
The simple sequential access dramatically reduces active pin count, facilitates hardware layout, increases system
reliability, minimizes switching noise, and reduces package size. The device is optimized for use in many
commercial and industrial applications where high-density, low-pin count, low-voltage and low-power are essential.
To allow for simple in-system reprogrammability, the Atmel AT45DB161D does not require high input voltages for
programming. The device operates from a single power supply, 2.5V to 3.6V or 2.7V to 3.6V, for both the program
and read operations. The AT45DB161D is enabled through the chip select pin (CS) and accessed via a three-wire
interface consisting of the Serial Input (SI), Serial Output (SO), and the Serial Clock (SCK).
All programming and erase cycles are self-timed.
Pin Configurations and Pinouts
1. The metal pad on the bottom of the MLF package is floating. This pad can be a “No Connect” or connected to GND
GND
VCC
SCK
Atmel AT45DB161D
WP
NC
NC
NC
NC
NC
SO
CS
SI
TSOP Top View: Type 1
MLF (VDFN) Top View
1
2
3
4
5
6
7
8
9
10
11
12
13
14
RESET
SCK
CS
SI
1
2
3
4
®
DataFlash
8
7
6
5
SO
GND
VCC
WP
®
uses a Atmel RapidS
28
27
26
25
24
23
22
21
20
19
18
17
16
15
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
™
serial interface to sequentially access its data.
Figure 2-2.
Figure 2-4.
RESET
SCK
A
B
C
D
E
CS
SI
BGA Package Ball-out
(Top View)
SOIC Top View
NC
NC
NC
NC
1
1
2
3
4
SCK
NC
SO
NC
CS
2
RDY/BSY
GND
NC
NC
3
SI
RESET
VCC
WP
NC
NC
4
8
7
6
5
3500N–DFLASH–05/10
NC
NC
NC
NC
NC
5
SO
GND
VCC
WP