TMP86C909XB Toshiba, TMP86C909XB Datasheet - Page 193

• Manufacturer Part Number: TMP86C909XB
• Description: EMULATION CHIP FOR TMP86F SDIP
• Manufacturer: Toshiba

Specifications of TMP86C909XB

• Accessory Type: Adapter
• For Use With/related Products: TMP86F SDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

17.3 DC Characteristics
17.3 DC Characteristics
Hysteresis voltage
Input current
Input resistance
Output high voltage
Output low voltage
Output low curren
Supply current in
NORMAL1, 2 modes
Supply current in IDLE
0, 1, 2 modes
Supply current in
SLOW1 mode
Supply current in
SLEEP1 mode
Supply current in
SLEEP0 mode
Supply current in
STOP mode
Peak current for
SLOW1 mode
(Note4,5)
Output leakage current
Program coutner (PC)
Parameter
Note 1: Typical values show those at Topr = 25°C and V
Note 2: Input current (I
Note 3: The supply currents of SLOW2 and SLEEP2 modes are equivalent to those of IDLE0, IDLE1 and IDLE2 modes.
Note 4: When a program is executing in the flash memory or when data is being read from the flash memory, the flash memory
Note 5: When designing the power supply, make sure that peak currents can be supplied. In SLOW1 mode, the difference
operates in an intermittent manner, causing peak currents in the operation current, as shown in Figure 17-1.
In this case, the supply current I
peak current and MCU current.
between the peak current and the average current becomes large.
Symbol
I
DDP-P
R
V
V
I
I
V
I
I
I
I
I
I
LO1
LO2
IN1
IN2
IN3
OL
DD
DDP-P
HS
IN3
OH
OL
[mA]
Figure 17-1 Intermittent Operation of Flash Memory
Hysteresis input
TEST
Sink open drain, tri–state port
RESET
RESET
Sink open drain port
Tri–state port
Tri–state port
Except XOUT, P3, P5
High current port
(P0 Port)
IN3
): The current through pull-up resistor is not included.
1 machine cycle (4/fc or 4/fs)
,
pull–up
STOP
n
Pins
DD
n+1
(in NORMAL1, NORMAL2 and SLOW1 modes) is defined as the sum of the average
n+2
Page 182
V
V
V
V
V
V
V
V
V
fc = 16 MHz
fs = 32.768 kHz
V
V
fs = 32.768 kHz
V
V
V
V
DD
DD
DD
DD
DD
DD
DD
DD
IN
DD
IN
DD
IN
DD
DD
DD
= 5.3 V/0.2 V
= 2.8 V/0.2 V
= 5.3 V/0.2 V
= 5.5 V, V
= 5.5 V, V
= 5.5 V, V
= 5.5 V, V
= 4.5 V, I
= 4.5 V, I
= 4.5 V, V
= 5.5 V
= 3.0 V
= 5.5 V
= 5.5 V
= 3.0 V
= 5 V.
n+3
OH
OL
IN
IN
OUT
OUT
OL
Condition
= 1.6 mA
= 5.5 V/0 V
= 0 V
= -0.7 mA
= 1.0 V
= 5.5 V
= 5.5 V/0 V
When a program
operates on flash
memory (Note5,6)
When a program
operates on flash
memory (Note5,6)
When a program
operates on RAM
Momentary flash current
Max. current
Typ. current
MCU current
100
Min
4.1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Sum of average
momentary flash current
and MCU current
(V
SS
= 0 V, Topr = -40 to 85 °C)
Typ.
10.5
220
0.9
4.5
0.5
20
25
15
10
–
–
–
–
–
7
5
2
TMP86F409NG
Max
450
0.4
8.5
±2
±2
19
65
25
15
12
10
–
2
–
–
–
–
Unit
mA
mA
mA
µA
kΩ
µA
µA
V
V