TMP86C993XB Toshiba, TMP86C993XB Datasheet - Page 58

• Manufacturer Part Number: TMP86C993XB
• Description: EMULATION CHIP FOR TMP86F SSOP
• Manufacturer: Toshiba

Specifications of TMP86C993XB

• Accessory Type: Adapter
• For Use With/related Products: TMP86F SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.7
External Interrupts
3.7
(Pulse inputs of less than a certain time are eliminated as noise).
interrupt input pin or an input/output port, and is configured as an input port during reset.
control register (EINTCR).
External Interrupts
The TMP86FH92DMG has 5 external interrupt inputs. These inputs are equipped with digital noise reject circuits
Edge selection is also possible with INT1,INT3,INT4. The INT0/P10 pin can be configured as either an external
Edge selection, noise reject control and INT0/P10 pin function selection are performed by the external interrupt
Note 1: In NORMAL1/2 or IDLE1/2 mode, if a signal with no noise is input on an external interrupt pin, it takes a maximum of
Note 2: When INT0EN = "0", IL5 is not set even if a falling edge is detected on the INT0 pin input.
Note 3: When a pin with more than one function is used as an output and a change occurs in data or input/output status, an
Source
INT0
INT1
INT3
INT4
INT5
"signal establishment time + 6/fs[s]" from the input signal's edge to set the interrupt latch.
interrupt request signal is generated in a pseudo manner. In this case, it is necessary to perform appropriate processing
such as disabling the interrupt enable flag.
INT0
INT1
INT3
INT4
INT5
Pin
IMF × EF5 × INT0EN=1
IMF × EF6 = 1
IMF × EF16 = 1
IMF × EF20 = 1
IMF × EF21 = 1
Enable Conditions
Falling edge
Falling edge
or
Rising edge
Falling edge
Rising edge
Falling and Rising edge
or
H level
Falling edge
Rising edge
Falling and Rising edge
or
H level
Falling edge
Page 44
Release Edge (level)
Pulses of less than 2/fc [s] are eliminated as
noise. Pulses of 7/fc [s] or more are considered
to be signals. In the SLOW or the SLEEP mode,
pulses of less than 1/fs [s] are eliminated as
noise. Pulses of 3.5/fs [s] or more are considered
to be signals.
Pulses of less than 15/fc or 63/fc [s] are elimina-
ted as noise. Pulses of 49/fc or 193/fc [s] or more
are considered to be signals. In the SLOW or the
SLEEP mode, pulses of less than 1/fs [s] are
eliminated as noise. Pulses of 3.5/fs [s] or more
are considered to be signals.
Pulses of less than 7/fc [s] are eliminated as
noise. Pulses of 25/fc [s] or more are considered
to be signals. In the SLOW or the SLEEP mode,
pulses of less than 1/fs [s] are eliminated as
noise. Pulses of 3.5/fs [s] or more are considered
to be signals.
Pulses of less than 7/fc [s] are eliminated as
noise. Pulses of 25/fc [s] or more are considered
to be signals. In the SLOW or the SLEEP mode,
pulses of less than 1/fs [s] are eliminated as
noise. Pulses of 3.5/fs [s] or more are considered
to be signals.
Pulses of less than 2/fc [s] are eliminated as
noise. Pulses of 7/fc [s] or more are considered
to be signals. In the SLOW or the SLEEP mode,
pulses of less than 1/fs [s] are eliminated as
noise. Pulses of 3.5/fs [s] or more are considered
to be signals.
Digital Noise Reject
TMP86FH92DMG