EVAL-ADUC7032QSPZ Analog Devices Inc, EVAL-ADUC7032QSPZ Datasheet - Page 25
![EVAL DEV QUICK START ADUC7032](/photos/9/24/92482/eval-aduc7032qspz_sml.jpg)
EVAL-ADUC7032QSPZ
Manufacturer Part Number
EVAL-ADUC7032QSPZ
Description
EVAL DEV QUICK START ADUC7032
Manufacturer
Analog Devices Inc
Series
QuickStart™ PLUS Kitr
Type
MCUr
Datasheet
1.EVAL-ADUC7032QSPZ.pdf
(116 pages)
Specifications of EVAL-ADUC7032QSPZ
Contents
Evaluation Board, Power Supply, Cable, Software, Emulator and Documentation
For Use With/related Products
ADuC7032
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
•
•
FEE0CON and FEE1CON Registers
Name: FEE0CON and FEE1CON
Address: 0xFFFF0E08 and 0xFFFF0E88
Default Value (Both Registers): 0x07
Access: Read/write
Function: These 8-bit registers are written by user code to control the operating modes of the Flash/EE memory controllers for Block 0
(32 kB) and Block 1 (64 kB).
Table 14. Command Codes in FEE0CON and FEE1CON
Code
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
1
2
x in the register names designates 0 or 1 for Flash/EE Block 0 or Flash/EE Block 1.
The FEExCON always reads 0x07 immediately after execution of any of these commands.
2
2
2
2
2
2
FEExHID (x = 0 or 1) is a protection MMR that controls
read- and write-protection of the Flash/EE memory code
space. If previously configured via the FEExPRO register,
FEExHID may require a software key to enable access.
FEExPRO (x = 0 or 1) is a buffer of the FEExHID register,
which is used to store the FEExHID value so it is automati-
cally downloaded to the FEExHID registers on subsequent
reset and power-on events.
2
Reserved
Single read
Single write
Erase-write
Single verify
Single erase
Mass erase
Reserved
Reserved
Reserved
Protect
Reserved
Reserved
Ping
Command
Signature
Description
Reserved. This command should not be written by user code.
Load FEExDAT with the 16-bit data indexed by FEExADR.
Write FEExDAT at the address pointed by FEExADR. This operation takes 50 μs.
Erase the page indexed by FEExADR and write FEExDAT at the location pointed by FEExADR. This operation
takes 20 ms.
Compare the contents of the location pointed by FEExADR to the data in FEExDAT. The result of the comparison
is returned in FEExSTA Bit 1.
Erase the page indexed by FEExADR.
Erase Block 0 (30 kB) or Block 1 (64 kB) of user space. The 2 kB kernel is protected. This operation takes 1.2 sec.
To prevent accidental execution, a command sequence is required to execute this instruction. This sequence is
described in the Command Sequence for Executing a Mass Erase section.
Default command.
Reserved. This command should not be written by user code.
Reserved. This command should not be written by user code.
Reserved. This command should not be written by user code.
FEE0CON. This command results in a 24-bit LFSR-based signature being generated and loaded into FEE0SIG.
If FEE0ADR is less than 0x97800, this command results in a 24-bit LFSR-based signature of the user code space
from the page specified in FEE0ADR upwards, including the kernel, security bits, and Flash/EE key.
If FEE0ADR is greater than 0x97800, the kernel and manufacturing data are signed.
FEE1CON. This command results in a 24-bit LFSR-based signature being generated, beginning at FEE1ADR and
ending at the end of the 64 kB block, and loaded into FEE1SIG. The last page of this block is not included in the
sign generation.
This command can be run only once. The value of FEExPRO is saved and can be removed only with a mass erase
(0x06) or with the software protection key.
Reserved. This command should not be written by user code.
Reserved. This command should not be written by user code.
No operation, interrupt generated.
1
Rev.0 | Page 25 of 116
Note that user software must ensure that the Flash/EE controller
has completed any erase or write cycle before the PLL is powered
down. If the PLL is powered down before an erase or write cycle
has completed, the Flash/EE page or byte may be corrupted.
The following sections describe in detail the bit designations of
each of the Flash/EE control MMRs.
ADuC7032-8L