EVAL-ADUC7032QSPZ Analog Devices Inc, EVAL-ADUC7032QSPZ Datasheet - Page 94
![EVAL DEV QUICK START ADUC7032](/photos/9/24/92482/eval-aduc7032qspz_sml.jpg)
EVAL-ADUC7032QSPZ
Manufacturer Part Number
EVAL-ADUC7032QSPZ
Description
EVAL DEV QUICK START ADUC7032
Manufacturer
Analog Devices Inc
Series
QuickStart™ PLUS Kitr
Type
MCUr
Datasheet
1.EVAL-ADUC7032QSPZ.pdf
(116 pages)
Specifications of EVAL-ADUC7032QSPZ
Contents
Evaluation Board, Power Supply, Cable, Software, Emulator and Documentation
For Use With/related Products
ADuC7032
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 94 of 116
- Download datasheet (3Mb)
ADuC7032-8L
HANDLING INTERRUPTS FROM THE HIGH
VOLTAGE PERIPHERAL CONTROL INTERFACE
An interrupt controller is also integrated with the high voltage
circuits. If enabled via IRQEN[16], one of five high voltage
sources can assert the high voltage interrupt (IRQ3) signal and
interrupt the MCU core.
While the MCU response to this interrupt event is, as normal, to
vector to the IRQ or FIQ interrupt vector address, the high voltage
interrupt controller simultaneously and automatically loads the
current value of the high voltage status register (HVSTA) into the
HVDAT register. During this time the busy bit, HVCON[0], is set
to indicate the transfer is in progress and clears after 10 μs to
indicate the HVSTA contents are available in HVDAT.
The interrupt handler can, therefore, poll the busy bit in HVCON
until it deasserts and then read the HVDAT register.
Table 78. High Voltage Diagnostics
High Voltage Pin
LIN
WU
Fault Condition
Short between
LIN and VBAT
Short between
LIN and GND
Short between
WU and VBAT
Short between
WU and GND
Open circuit
Method
Drive LIN low
Drive LIN high
Drive WU low
Drive WU high
Enable OC diagnostic resistor with
WU disabled
Rev.0 | Page 94 of 116
At this time, HVDAT holds the value of the HVSTA register.
The status flags can then be interrogated to determine the exact
source of the high voltage interrupt and take appropriate action.
LOW VOLTAGE FLAG (LVF)
The ADuC7032-8L features a low voltage flag (LVF) that, when
enabled, allows the user to monitor REG_DVDD. When
enabled via HVCFG0[2], the low voltage flag can be monitored
through HVMON[3]. If REG_DVDD drops below 2.1 V,
HVMON[3] is cleared. If REG_DVDD drops below 2.1 V,
the RAM contents are corrupted. Once the low voltage flag is
enabled, it is reset only by REG_DVDD dropping below 2.1 V
or the disabling of the LVF functionality using HVCFG0[2].
HIGH VOLTAGE DIAGNOSTICS
It is possible to diagnose fault conditions on the WU and LIN
bus, as detailed in Table 78.
Result
LIN short-circuit interrupt is generated after 20 μs
if more than 100 mA is drawn continuously.
LIN readback low.
Readback high.
WU short-circuit interrupt is generated after 400 μs if more
than 200 mA is sourced.
HVMON[7] is cleared if load is connected; HVMON[7] is set
if WU is open-circuited.
Related parts for EVAL-ADUC7032QSPZ
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![SI9182DH-AD-T1-E3](/photos/19/9/190940/3752004_tmb.jpg)
Part Number:
Description:
IC, ADJ LDO REG, 1.5V TO 5V 250mA MSOP-8
Manufacturer:
Vishay
Datasheet:
![SI9181DQ-AD-T1](/photos/19/9/190951/3752002_tmb.jpg)
Part Number:
Description:
IC, ADJ LDO REG, 1.5V TO 5V 0.6A 8-TSSOP
Manufacturer:
Vishay
Datasheet:
![SI9182DH-AD-T1](/photos/19/9/190940/3752004_tmb.jpg)
Part Number:
Description:
IC, ADJ LDO REG, 1.5V TO 5V 250mA MSOP-8
Manufacturer:
Vishay
Datasheet:
![SI9183DT-AD-T1](/photos/19/8/190864/3752006_tmb.jpg)
Part Number:
Description:
IC ADJ LDO REG 1.5V TO 5V 150mA 5-SOT-23
Manufacturer:
Vishay
Datasheet:
![AS1324-AD EB](/images/manufacturer_photos/0/0/84/austriamicrosystems_tmb.jpg)
Part Number:
Description:
BOARD EVAL AS1324-AD
Manufacturer:
austriamicrosystems
Datasheet:
![SI9181DQ-AD-T1-E3](/photos/19/9/190951/3752002_tmb.jpg)
Part Number:
Description:
IC, ADJ LDO REG, 1.5V TO 5V 0.6A 8-TSSOP
Manufacturer:
Vishay
Datasheet:
![SI91821DH-AD-T1](/photos/18/99/189923/3833557_tmb.gif)
Part Number:
Description:
IC, ADJ LDO REG, 1.5V TO 5V, 0.3A, MSOP8
Manufacturer:
Vishay
Datasheet:
![SI91821DH-AD-T1-E3](/photos/18/99/189923/3833557_tmb.gif)
Part Number:
Description:
IC, ADJ LDO REG, 1.5V TO 5V, 0.3A, MSOP8
Manufacturer:
Vishay
Datasheet:
![SI91822DH-AD-T1](/photos/18/99/189923/3833557_tmb.gif)
Part Number:
Description:
IC, ADJ LDO REG 1.215V TO 5V 0.3A MSOP-8
Manufacturer:
Vishay
Datasheet:
![SI91822DH-AD-T1-E3](/photos/18/99/189923/3833557_tmb.gif)
Part Number:
Description:
IC, ADJ LDO REG 1.215V TO 5V 0.3A MSOP-8
Manufacturer:
Vishay
Datasheet:
![ADXL203EB](/photos/9/18/91808/adxl203eb_tmb.jpg)
Part Number:
Description:
±1.7g Dual-Axis IMEMS Accelerometer Evaluation Board
Manufacturer:
Analog Devices Inc
Datasheet:
![AD633JRZ-R7](/photos/5/66/56684/505-8-soic_tmb.jpg)
Part Number:
Description:
IC MULTIPLIER ANALOG 8-SOIC T/R
Manufacturer:
Analog Devices Inc
Datasheet:
![AD633JN](/images/manufacturer_photos/0/0/57/analog_devices_inc_tmb.jpg)
Part Number:
Description:
IC ANALOG MULTIPLIER 8-DIP
Manufacturer:
Analog Devices Inc
Datasheet:
![AD633JR](/photos/5/66/56684/505-8-soic_tmb.jpg)
Part Number:
Description:
IC ANALOG MULTIPLIER 8-SOIC
Manufacturer:
Analog Devices Inc
Datasheet:
![AD633ANZ](/images/manufacturer_photos/0/0/57/analog_devices_inc_tmb.jpg)
Part Number:
Description:
IC ANALOG MULTIPLIER 8-DIP
Manufacturer:
Analog Devices Inc
Datasheet: