Z8F3222AR020SG Zilog, Z8F3222AR020SG Datasheet - Page 115

• Manufacturer Part Number: Z8F3222AR020SG
• Description: IC ENCORE MCU FLASH 32K 64LQFP
• Manufacturer: Zilog
• Series: Encore!® XP®r

Specifications of Z8F3222AR020SG

• Core Processor: Z8
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 46
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 64-LQFP
• Processor Series: Z8F322x
• Core: eZ8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 46
• Number Of Timers: 4
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 770-1002 - ISP 4PORT ZILOG Z8 ENCORE! MCU269-4643 - KIT DEV Z8 ENCORE XP 28-PIN269-4630 - DEV KIT FOR Z8 ENCORE 8K/4K269-4629 - KIT DEV Z8 ENCORE XP 28-PIN269-4628 - KIT DEV Z8 ENCORE XP 8-PIN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 269-4261; Z8F3222AR020SG

PS019921-0308
1
0
Idle State
1
0
of Line
Transmitting Data using the Polled Method
Idle State
of Line
Follow the steps below to transmit data using the polled method of operation:
1. Write to the UART Baud Rate High and Low Byte registers to set the desired baud
2. Enable the UART pin functions by configuring the associated GPIO Port pins for
3. If MULTIPROCESSOR mode is desired, write to the UART Control 1 register to
4. Write to the UART Control 0 register to:
Start
Figure 13. UART Asynchronous Data Format without Parity
Start
Figure 14. UART Asynchronous Data Format with Parity
rate.
alternate function operation.
enable MULTIPROCESSOR (9-bit) mode functions.
–
–
–
Bit0
Set the MULTIPROCESSOR Mode Select (MPEN) to Enable
MULTIPROCESSOR mode.
Set the transmit enable bit (TEN) to enable the UART for data transmission
If parity is desired and MULTIPROCESSOR mode is not enabled, set the parity
enable bit (PEN) and select either Even or Odd parity (PSEL).
lsb
Bit0
lsb
Bit1
Bit1
Bit2
Bit2
Bit3
Data Field
Bit3
Data Field
Bit4
Bit4
Bit5
Bit5
Bit6
Z8 Encore! XP
Bit6
msb
Bit7
msb
Bit7
Product Specification
Parity
®
1
Stop Bit(s)
F64XX Series
1
2
Stop Bit(s)
2
UART
101