Z8F3222AR020SG Zilog, Z8F3222AR020SG Datasheet - Page 119

• Manufacturer Part Number: Z8F3222AR020SG
• Description: IC ENCORE MCU FLASH 32K 64LQFP
• Manufacturer: Zilog
• Series: Encore!® XP®r

Specifications of Z8F3222AR020SG

• Core Processor: Z8
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 46
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 64-LQFP
• Processor Series: Z8F322x
• Core: eZ8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 46
• Number Of Timers: 4
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 770-1002 - ISP 4PORT ZILOG Z8 ENCORE! MCU269-4643 - KIT DEV Z8 ENCORE XP 28-PIN269-4630 - DEV KIT FOR Z8 ENCORE 8K/4K269-4629 - KIT DEV Z8 ENCORE XP 28-PIN269-4628 - KIT DEV Z8 ENCORE XP 8-PIN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 269-4261; Z8F3222AR020SG

PS019921-0308
1
0
Idle State
of Line
Clear To Send (CTS) Operation
MULTIPROCESSOR (9-bit) Mode
Figure 15. UART Asynchronous MULTIPROCESSOR Mode Data Format
3. Clear the UART Receiver interrupt in the applicable Interrupt Request register.
4. Execute the IRET instruction to return from the interrupt-service routine and await
The CTS pin, if enabled by the CTSE bit of the UART Control 0 register, performs flow
control on the outgoing transmit datastream. The Clear To Send (CTS) input pin is sam-
pled one system clock before beginning any new character transmission. To delay trans-
mission of the next data character, an external receiver must deassert CTS at least one
system clock cycle before a new data transmission begins. For multiple character trans-
missions, this would typically be done during Stop Bit transmission. If CTS deasserts in
the middle of a character transmission, the current character is sent completely.
The UART has a MULTIPROCESSOR (9-bit) mode that uses an extra (9th) bit for selec-
tive communication when a number of processors share a common UART bus. In MULTI-
PROCESSOR mode (also referred to as 9-Bit mode), the multiprocessor bit (MP) is
transmitted immediately following the 8-bits of data and immediately preceding the Stop
bit(s) as displayed in
In MULTIPROCESSOR (9-bit) mode, the Parity bit location (9th bit) becomes the MUL-
TIPROCESSOR control bit. The UART Control 1 and Status 1 registers provide MULTI-
PROCESSOR (9-bit) mode control and status information. If an automatic address
matching scheme is enabled, the UART Address Compare register holds the network
address of the device.
MULTIPROCESSOR (9-bit) Mode Receive Interrupts
When MULTIPROCESSOR mode is enabled, the UART only processes frames addressed
to it. The determination of whether a frame of data is addressed to the UART can be made
in hardware, software or some combination of the two, depending on the multiprocessor
Start
more data.
Bit0
lsb
Bit1
Figure
Bit2
15. The character format is:
Bit3
Data Field
Bit4
Bit5
Bit6
Z8 Encore! XP
msb
Bit7
Product Specification
MP
®
F64XX Series
1
Stop Bit(s)
2
UART
105