PIC18F87J11-I/PT Microchip Technology, PIC18F87J11-I/PT Datasheet - Page 227

• Manufacturer Part Number: PIC18F87J11-I/PT
• Description: IC PIC MCU FLASH 64KX16 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F87J11-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: 80-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Ram Size: 3930 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 15x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3904 B
• Interface Type: EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 68
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DM183022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 15-ch x 10-bit
• Package: 80TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 1.8|2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DV164136 - DEVELOPMENT KIT FOR PIC18AC162091 - HEADER MPLAB ICD2 18F87J11 64/80MA180020 - MODULE PLUG-IN HPC EXPL 18F87J11AC164328 - MODULE SKT FOR 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

19.3.4
To enable the serial port, MSSP Enable bit, SSPEN
(SSPxCON1<5>), must be set. To reset or reconfigure
SPI mode, clear the SSPEN bit, reinitialize the
SSPxCON registers and then set the SSPEN bit. This
configures the SDIx, SDOx, SCKx and SSx pins as
serial port pins. For the pins to behave as the serial port
function, some must have their data direction bits (in
the TRIS register) appropriately programmed as
follows:
• SDIx is automatically controlled by the
• SDOx must have the TRISC<5> or TRISD<4> bit
• SCKx (Master mode) must have the TRISC<3> or
• SCKx (Slave mode) must have the TRISC<3> or
• SSx must have the TRISF<7> or TRISD<7> bit
FIGURE 19-2:
© 2009 Microchip Technology Inc.
SPI module
cleared
TRISD<6>bit cleared
TRISD<6> bit set
set
SPI Master SSPM3:SSPM0 = 00xxb
ENABLING SPI I/O
MSb
PROCESSOR 1
Serial Input Buffer
SPI MASTER/SLAVE CONNECTION
Shift Register
(SSPxBUF)
(SSPxSR)
LSb
SDOx
SCKx
SDIx
Serial Clock
PIC18F87J11 FAMILY
Any serial port function that is not desired may be
overridden by programming the corresponding Data
Direction (TRIS) register to the opposite value.
19.3.5
Figure 19-2 shows a typical connection between two
microcontrollers. The master controller (Processor 1)
initiates the data transfer by sending the SCKx signal.
Data is shifted out of both shift registers on their pro-
grammed clock edge and latched on the opposite edge
of the clock. Both processors should be programmed to
the same Clock Polarity (CKP), then both controllers
would send and receive data at the same time.
Whether the data is meaningful (or dummy data)
depends on the application software. This leads to
three scenarios for data transmission:
• Master sends data – Slave sends dummy data
• Master sends data – Slave sends data
• Master sends dummy data – Slave sends data
SDOx
SCKx
SDIx
SPI Slave SSPM3:SSPM0 = 010xb
TYPICAL CONNECTION
MSb
Serial Input Buffer
Shift Register
(SSPxBUF)
PROCESSOR 2
(SSPxSR)
LSb
DS39778D-page 227