PIC18F4580T-I/PT Microchip Technology, PIC18F4580T-I/PT Datasheet - Page 31

• Manufacturer Part Number: PIC18F4580T-I/PT
• Description: IC PIC MCU FLASH 16KX16 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4580T-I/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

3.4
For timing insensitive applications, the “RC” and
“RCIO” device options offer additional cost savings.
The actual oscillator frequency is a function of several
factors:
• supply voltage
• values of the external resistor (R
• operating temperature
Given the same device, operating voltage and tempera-
ture and component values, there will also be unit-to-unit
frequency variations. These are due to factors such as:
• normal manufacturing variation
• difference in lead frame capacitance between
• variations within the tolerance of limits of R
In the RC Oscillator mode, the oscillator frequency
divided by 4 is available on the OSC2 pin. This signal
may be used for test purposes or to synchronize other
logic. Figure 3-5 shows how the R/C combination is
connected.
FIGURE 3-5:
The RCIO Oscillator mode (Figure 3-6) functions like
the RC mode, except that the OSC2 pin becomes an
additional general purpose I/O pin. The I/O pin
becomes bit 6 of PORTA (RA6).
FIGURE 3-6:
© 2009 Microchip Technology Inc.
Recommended values: 3 kΩ ≤ R
R
C
R
C
Recommended values: 3 kΩ ≤ R
capacitor (C
package types (especially for low C
and C
V
V
EXT
EXT
EXT
EXT
SS
SS
V
V
DD
DD
EXT
RC Oscillator
RA6
F
EXT
OSC
)
/4
OSC1
OSC1
OSC2/CLKO
RC OSCILLATOR MODE
RCIO OSCILLATOR MODE
I/O (OSC2)
C
C
EXT
EXT
> 20 pF
> 20 pF
EXT
EXT
EXT
≤ 100 kΩ
≤ 100 kΩ
PIC18FXXXX
EXT
PIC18FXXXX
) and
values)
Internal
Internal
Clock
Clock
EXT
PIC18F2480/2580/4480/4580
3.5
A Phase Locked Loop (PLL) circuit is provided as an
option for users who wish to use a lower frequency
oscillator circuit or to clock the device up to its highest
rated frequency from a crystal oscillator. This may be
useful for customers who are concerned with EMI due
to high-frequency crystals or users who require higher
clock speeds from an internal oscillator.
3.5.1
The HSPLL mode makes use of the HS mode oscillator
for frequencies up to 10 MHz. A PLL then multiplies the
oscillator output frequency by 4 to produce an internal
clock frequency up to 40 MHz.
The PLL is only available to the crystal oscillator when
the FOSC<3:0> Configuration bits are programmed for
HSPLL mode (= 0110).
FIGURE 3-7:
3.5.2
The PLL is also available to the internal oscillator block
in selected oscillator modes. In this configuration, the
PLL is enabled in software and generates a clock
output of up to 32 MHz. The operation of INTOSC with
the PLL is described in Section 3.6.4 “PLL in INTOSC
Modes”.
OSC2
OSC1
PLL Frequency Multiplier
(from Configuration Register 1H)
HS Mode
HSPLL OSCILLATOR MODE
PLL AND INTOSC
Crystal
Osc
HS Osc Enable
PLL Enable
F
F
÷4
PLL BLOCK DIAGRAM
(HS MODE)
IN
OUT
Comparator
Loop
Filter
Phase
VCO
DS39637D-page 31
SYSCLK