STM32F103C6T7A STMicroelectronics, STM32F103C6T7A Datasheet - Page 56

• Manufacturer Part Number: STM32F103C6T7A
• Description: MCU ARM 32BIT 32KB FLASH 48LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103C6T7A

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Featured Product: STM32 Cortex-M3 Companion Products
• Eeprom Size: -
• Cpu Family: STM32
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Interface Type: CAN/I2C/SPI/USART
• Total Internal Ram Size: 10KB
• # I/os (max): 37
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• On-chip Adc: 2(10-chx12-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Electrical characteristics
5.3.13
Table 35.
1. FT = Five-volt tolerant. In order to sustain a voltage higher than V
2. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization, not tested in production.
3. With a minimum of 100 mV.
4. Leakage could be higher than max. if negative current is injected on adjacent pins.
5. Pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. This
56/87
Symbol
V
R
R
C
V
V
I
disabled.
PMOS/NMOS contribution
lkg
hys
PU
PD
IH
IO
IL
Standard IO input low
level voltage
IO FT
voltage
Standard IO input high
level voltage
IO FT
voltage
Standard IO Schmitt
trigger voltage
hysteresis
IO FT Schmitt trigger
voltage hysteresis
Input leakage current
Weak pull-up equivalent
resistor
Weak pull-down
equivalent resistor
I/O pin capacitance
I/O port characteristics
General input/output characteristics
Unless otherwise specified, the parameters given in
performed under the conditions summarized in
compliant.
I/O static characteristics
(1)
(1)
Parameter
(5)
input low level
input high level
(2)
to the series resistance is minimum
(2)
(5)
(4)
V
V
V
DD
DD
Standard I/Os
SS
Conditions
V
V
> 2 V
≤
V
≤
I/O FT
IN
IN
IN
2 V
V
=
=
= 5 V
IN
V
V
≤
DD
SS
Doc ID 15060 Rev 5
V
DD
(~10% order)
0.41*(V
0.42*(V
5% V
DD
DD
+0.3 the internal pull-up/pull-down resistors must be
DD
–0.3
–0.3
Min
200
30
30
-2 V)+1.3 V
Table
-2 V)+1 V
DD
.
(3)
Table 35
9. All I/Os are CMOS and TTL
Typ
40
40
5
STM32F103x4, STM32F103x6
are derived from tests
0.32*(V
0.28*(V
V
DD
DD
DD
Max
5.5
5.2
50
50
±1
-2V)+0.75 V
-2 V)+0.8 V
3
+0.3
Unit
mV
mV
µA
kΩ
kΩ
pF
V
V
V
V