UPD78F0533AGB-GAH-AX Renesas Electronics America, UPD78F0533AGB-GAH-AX Datasheet - Page 727

• Manufacturer Part Number: UPD78F0533AGB-GAH-AX
• Description: MCU 8BIT 64-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0/Kx2r

Specifications of UPD78F0533AGB-GAH-AX

• Core Processor: 78K/0
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 55
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0/Kx2
under the recommended connection of unused pins shown in Table 2-3 Pin I/O Circuit Types, or those described in
Table 27-4 Processing of Unused Pins When the Flash Memory Write Adapter Is Connected (Required).
27.6 Connection of Pins on Board
provided on the target system.
programming mode on the board.
same status as immediately after reset. Therefore, if the external device does not recognize the state immediately after
reset, the pins must be handled as described below.
R01UH0008EJ0401 Rev.4.01
Jul 15, 2010
For the pins not to be used when the dedicated program adapter (FA series) is used, perform the processing described
To write the flash memory on-board, connectors that connect the dedicated flash memory programmer must be
When the flash memory programming mode is set, all the pins not used for programming the flash memory are in the
Table 27-4. Processing of Unused Pins When the Flash Memory Write Adapter Is Connected (Required)
Notes 1.
P00, P01
P03 to P06
P10, P11
P14
P16, P17
P30 to P33
P60 to P63
P70 to P77
P120
P140 to P143
2.
3.
4.
5.
Pin name
These pins may be directly connected to EV
is performed so that operation is not switched to the normal operation mode on the
flash memory write adapter board during flash memory programming.
These pins may be left open with the
78K0/KE2 as well as the 78K0/KD2.
Connect these pins with the programmer when communicating with the dedicated
flash memory programmer via serial communication by CSI10.
Connect this pin with the programmer when communicating with the dedicated flash
memory programmer via serial communication by UART6.
With products without an EV
EV
DD
pin, connect them to V
First provide a function that selects the normal operation mode or flash memory
Independently connect to EV
Independently connect to EV
Independently connect to EV
Independently connect to EV
Independently connect to EV
Independently connect to EV
EV
Independently connect to EV
SS
.
Note 5
DD
SS
.
pin, connect them to V
μ
PD78F053n and 78F053nA (n = 1 to 3) of the
SS
SS
SS
SS
SS
SS
SS
Pin processing
via a resistor.
via a resistor.
via a resistor.
via a resistor.
via a resistor.
via a resistor, or connect directly to
via a resistor.
SS
, without using a resistor, when design
Notes 1, 5
Notes 2, 5
Notes 3, 5
Notes 4, 5
Notes 1, 5
Notes 1, 5
SS
. With products without an
CHAPTER 27 FLASH MEMORY
727