UPD78F0533AGB-GAH-AX Renesas Electronics America, UPD78F0533AGB-GAH-AX Datasheet - Page 807

• Manufacturer Part Number: UPD78F0533AGB-GAH-AX
• Description: MCU 8BIT 64-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0/Kx2r

Specifications of UPD78F0533AGB-GAH-AX

• Core Processor: 78K/0
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 55
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0/Kx2
Caution The pins mounted depend on the product. Refer to Caution at the beginning of this chapter.
Internal Oscillator Characteristics
(T
Note Indicates only oscillator characteristics. Refer to AC Characteristics for instruction execution time.
Remark RSTS: Bit 7 of the internal oscillation mode register (RCM)
XT1 Oscillator Characteristics
(T
Notes 1. The 78K0/KB2 is not provided with the XT1 oscillator.
Cautions 1. When using the XT1 oscillator, wire as follows in the area enclosed by the broken lines in the above
Remark For the resonator selection and oscillator constant, customers are requested to either evaluate the oscillation
R01UH0008EJ0401 Rev.4.01
Jul 15, 2010
8 MHz internal oscillator
240 kHz internal oscillator
Crystal
resonator
A
A
Resonator
= −40 to +85°C, 1.8 V ≤ V
= −40 to +85°C, 1.8 V ≤ V
2. Indicates only oscillator characteristics. Refer to AC Characteristics for instruction execution time.
Resonator
2. The XT1 oscillator is designed as a low-amplitude circuit for reducing power consumption, and is
themselves or apply to the resonator manufacturer for evaluation.
figure to avoid an adverse effect from wiring capacitance.
• Keep the wiring length as short as possible.
• Do not cross the wiring with the other signal lines.
• Do not route the wiring near a signal line through which a high fluctuating current flows.
• Always make the ground point of the oscillator capacitor the same potential as V
• Do not ground the capacitor to a ground pattern through which a high current flows.
• Do not fetch signals from the oscillator.
more prone to malfunction due to noise than the X1 oscillator. Particular care is therefore required
with the wiring method when the XT1 clock is used.
Recommended Circuit
V
SS
C4
Rd
XT2
Internal high-speed oscillation
clock frequency (f
Internal low-speed oscillation
clock frequency (f
C3
DD
DD
XT1
Note 1
= EV
= EV
Parameter
CHAPTER 31 ELECTRICAL SPECIFICATIONS ((A) GRADE PRODUCTS)
DD
DD
XT1 clock oscillation
frequency (f
≤ 5.5 V, V
≤ 5.5 V, V
RH
RL
)
)
Note
Parameter
SS
SS
XT
)
= EV
= EV
Note 2
RSTS = 1
RSTS = 0
2.7 V ≤ V
1.8 V ≤ V
SS
SS
= AV
= AV
DD
DD
SS
SS
Conditions
≤ 5.5 V
< 2.7 V
2.7 V ≤ V
1.8 V ≤ V
= 0 V)
= 0 V)
Conditions
DD
DD
≤ 5.5 V
< 2.7 V
MIN.
MIN.
2.48
216
192
7.6
7.6
32
32.768
TYP.
TYP.
240
240
8.0
8.0
5.6
SS
MAX.
MAX.
10.4
9.86
264
264
8.4
35
.
MHz
MHz
MHz
Unit
kHz
kHz
Unit
kHz
807