MAXQ2010-RFX+ Maxim Integrated Products, MAXQ2010-RFX+ Datasheet - Page 25

• Manufacturer Part Number: MAXQ2010-RFX+
• Description: IC MCU 16BIT 64KB FLASH 100-LQFP
• Manufacturer: Maxim Integrated Products
• Series: MAXQ™r

Specifications of MAXQ2010-RFX+

• Core Processor: RISC
• Core Size: 16-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 55
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: MAXQ2010
• Core: RISC
• Data Bus Width: 16 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 10 MHz
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Controller Family/series: MAXQ
• No. Of I/o's: 43
• Ram Memory Size: 2048Byte
• Cpu Speed: 10MHz
• No. Of Timers: 3
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Number Of Programmable I/os: 55
• Development Tools By Supplier: MAXQ2010-KIT
• Package: 100LQFP
• Family Name: MAXQ
• Maximum Speed: 10 MHz
• On-chip Adc: 8-chx12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Figure 6. Type C/D Port Pin Schematic
The supply voltage monitor can detect if the supply volt-
age has fallen below a user-selectable level. If this hap-
pens, the microcontroller can be programmed to
generate an interrupt to inform the system. The detec-
tion level is set using the supply voltage threshold bit
(SVTH) and can be adjusted from 2.7V to 3.5V in 0.1V
increments. Setting the SVMEN bit to 1 enables the sup-
ply voltage monitor. Once the monitoring circuitry is sta-
ble and ready for operation, the supply voltage monitor
ready (SVMRDY) flag is set to 1. The default set point is
2.7V (SVTH[3:0] = 07h). Care must be taken not to set
the set point below 2.7V as SVM interrupts may not
occur because the brownout monitor may activate first.
The supply voltage monitor causes a switchback to
occur if the supply voltage falls below the threshold
value and the supply voltage monitor interrupt is
enabled (SVMIE = 1).
The supply voltage monitor remains operational in stop
mode if the supply voltage monitor stop mode enable
PI.x OR SF INPUT
SF DIRECTION
FLAG
SF OUTPUT
______________________________________________________________________________________
Supply Voltage Monitor
SF ENABLE
PD.x
PO.x
INTERRUPT
FLAG
16-Bit Mixed-Signal Microcontroller
CIRCUIT
DETECT
EIES.x
TYPE D PORT ONLY
bit (SVMSTOP) is set to 1. Clearing SVMSTOP to 0 dis-
ables the supply voltage monitor on entry to stop mode
if the SVM peripheral is enabled. If the supply voltage
monitor is enabled during stop mode, an SVMI interrupt
causes the processor to exit stop mode if enabled
(SVMIE = 1).
The microcontroller supports two independent USARTs
as well as I
cation ports.
The independent USARTs provide transmit and receive
signals to communicate with other RS-232 interface-
enabled devices, as well as PCs and serial modems
when paired with an external RS-232 line driver/receiver.
The dual independent USARTs can communicate simulta-
neously at different baud rates with two separate periph-
erals. The USART can detect framing errors and indicate
the condition through a user-accessible software bit.
MAXQ2010
I/O PAD
with LCD Interface
2
C master/slave and SPI master communi-
V
DDIO
V
WEAK
DDIO
Serial Peripherals
USART Serial Ports
PORT PIN
25