MAXQ2010-RFX+ Maxim Integrated Products, MAXQ2010-RFX+ Datasheet - Page 27

• Manufacturer Part Number: MAXQ2010-RFX+
• Description: IC MCU 16BIT 64KB FLASH 100-LQFP
• Manufacturer: Maxim Integrated Products
• Series: MAXQ™r

Specifications of MAXQ2010-RFX+

• Core Processor: RISC
• Core Size: 16-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 55
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: MAXQ2010
• Core: RISC
• Data Bus Width: 16 bit
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 10 MHz
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Controller Family/series: MAXQ
• No. Of I/o's: 43
• Ram Memory Size: 2048Byte
• Cpu Speed: 10MHz
• No. Of Timers: 3
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Number Of Programmable I/os: 55
• Development Tools By Supplier: MAXQ2010-KIT
• Package: 100LQFP
• Family Name: MAXQ
• Maximum Speed: 10 MHz
• On-chip Adc: 8-chx12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

ranges from 0000h to the value stored in the 16-bit cap-
ture/reload register (TBR), whereas in other implemen-
tations (e.g., Timer 1) the count ranges from the value
in the reload register to FFFFh. These timers are fully
described in the MAXQ Family User’s Guide .
Timer B operational modes include the following:
• Autoreload
• Autoreload Using External Pin
• Capture Using External Pin
• Up/Down Count Using External Pin
• Up-Count PWM/Output
• Up/Down PWM/Output
• Clock Output on TBB Pin
An internal watchdog timer greatly increases system reli-
ability. The timer resets the device if software execution
is disturbed. The watchdog timer is a free-running
counter designed to be periodically reset by the applica-
tion software. If software is operating correctly, the
counter is periodically reset and never reaches its maxi-
mum count. However, if software operation is interrupted,
the timer does not reset, triggering a system reset and
optionally a watchdog timer interrupt. This protects the
system against electrical noise or electrostatic discharge
(ESD) upsets that could cause uncontrolled processor
operation. The internal watchdog timer is an upgrade to
older designs with external watchdog devices, reducing
system cost and simultaneously increasing reliability.
The watchdog timer is controlled through bits in the
WDCN register. Its timeout period can be set to one of
four programmable intervals ranging from 2
system clocks in its default mode, allowing flexibility to
support different types of applications. The interrupt
occurs 512 system clocks before the reset, allowing the
system to execute an interrupt and place the system in
a known, safe state before the device performs a total
system reset. At 8MHz, watchdog timeout periods can
be programmed from 512µs to 67s, depending on the
system clock mode.
The internal hardware multiplier supports high-speed
multiplications. The multiplier can complete a 16-bit x
16-bit multiply-and-accumulate/subtract operation in a
single cycle with the support of a 48-bit accumulator.
The multiplier is a fixed-point arithmetic unit. The
operands can be either signed or unsigned numbers,
but the data type must be defined by the application
software prior to loading the operand registers.
______________________________________________________________________________________
Hardware Multiplier
Watchdog Timer
16-Bit Mixed-Signal Microcontroller
12
to 2
21
Seven different multiply operations can be performed
without requiring direct intervention of the microcon-
troller core. These include the following:
• Unsigned 16-bit multiplication
• Unsigned 16-bit multiplication and accumulation
• Unsigned 16-bit multiplication and subtraction
• Signed 16-bit multiplication
• Signed 16-bit multiplication and negate
• Signed 16-bit multiplication and accumulation
• Signed 16-bit multiplication and subtraction
Each of these operations is controlled and accessed
through six SFR registers. The 8-bit multiplier control
register (MCNT) selects the operation, data type,
operand count, optional hardware-based square func-
tion, write option on the MC register, the overflow flag,
and the clear control for operand registers and accu-
mulator. Loading and unloading of the data is achieved
through five 16-bit SFR registers.
Only one cycle is needed for computation. This means
that the result of an operation is ready in the next cycle
immediately following the loading of the last operand.
Back-to-back operations can be performed without wait
states between operations, independent of data type
and operand count.
The MAXQ2010 contains a 12-bit successive approxi-
mation analog-to-digital converter (ADC) with an analog
mux (Figure 7). The mux selects the ADC input from
eight single-ended channels or four differential chan-
nels. An internal precision bandgap reference can be
used for the ADC reference voltage, or the reference
voltage can be externally driven. Additionally, the ana-
log supply voltage (AVDD) can also be used as the
voltage reference. The ADC runs off a 2.7V to 3.6V
power supply and at a conversion rate up to 300ksps.
The ADC block includes a 12-bit SAR core, ADC con-
trols, a reference generator, and a circular block of six-
teen 12-bit data buffers. The ADC is controlled by SFR
registers. An autoscan feature allows the user to select
up to eight sampling channels for storage in the 16
memory locations.
There are two conversion modes: single-sequence
mode and continuous-sequence mode.
The ADC’s internal power-management system auto-
matically powers down when the conversion(s) are
done (ADCONV = 0). The start conversion bit,
ADCONV, is used to start all conversion processes. If
the ADC power-management override bit is cleared
with LCD Interface
Analog-to-Digital Converter
27