PIC24FJ256GB106-I/MR Microchip Technology, PIC24FJ256GB106-I/MR Datasheet - Page 15

• Manufacturer Part Number: PIC24FJ256GB106-I/MR
• Description: IC, 16BIT MCU, PIC24F, 32MHZ, QFN-64
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ256GB106-I/MR

• Controller Family/series: PIC24
• No. Of I/o's: 51
• Ram Memory Size: 16KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Core Size: 16 Bit
• Program Memory Size: 256KB
• Peripherals: ADC, Comparator, PWM, RTC, Timer
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, SPI, UART/USART, USB OTG
• Number Of I /o: 51
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN, Exposed Pad
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 52
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARD
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

3.4
3.4.1
Flash memory write and erase operations are controlled
by the NVMCON register. Programming is performed by
setting NVMCON to select the type of erase operation
(Table 3-2) or write operation (Table 3-3) and initiating
the programming by setting the WR control bit
(NVMCON<15>).
In ICSP mode, all programming operations are
self-timed. There is an internal delay between the user
setting the WR control bit and the automatic clearing of
the WR control bit when the programming operation
is complete. Please refer to Section 7.0 “AC/DC
Characteristics and Timing Requirements” for
information about the delays associated with various
programming operations.
TABLE 3-2:
TABLE 3-3:
3.4.2
The WR bit (NVMCON<15>) is used to start an erase or
write cycle. Setting the WR bit initiates the programming
cycle.
All erase and write cycles are self-timed. The WR bit
should be polled to determine if the erase or write cycle
has been completed. Starting a programming cycle is
performed as follows:
© 2007 Microchip Technology Inc.
404Fh
4042h
4003h
4001h
NVMCON
NVMCON
Value
Value
BSET
Flash Memory Programming in
ICSP Mode
PROGRAMMING OPERATIONS
STARTING AND STOPPING A
PROGRAMMING CYCLE
Write a Configuration Word register.
Program 1 row (64 instruction words) of
code memory or executive memory.
Erase all code memory, executive
memory and Configuration registers
(does not erase Unit ID or Device ID
registers).
Erase a page of code memory or
executive memory.
NVMCON, #WR
NVMCON ERASE
OPERATIONS
NVMCON WRITE
OPERATIONS
Erase Operation
Write Operation
PIC24FJXXXGA1/GB1
3.5
The procedure for erasing program memory (all of code
memory, data memory, executive memory and
code-protect bits) consists of setting NVMCON to
404Fh and executing the programming cycle.
A Chip Erase can erase all of user memory or all of both
the user and configuration memory. A table write
instruction should be executed prior to performing the
Chip Erase to select which sections are erased.
When this table write instruction is executed:
• If the TBLPAG register points to user space (is
• If TBLPAG points to configuration space (is
Figure 3-5 shows the ICSP programming process for
performing a Chip Erase. This process includes the
ICSP command code, which must be transmitted (for
each instruction), Least Significant bit first, using the
PGCx and PGDx pins (see Figure 3-2).
FIGURE 3-5:
less than 0x80), the Chip Erase will erase only
user memory.
greater than or equal to 0x80), the Chip Erase will
erase both user and configuration memory.
If configuration memory is erased, the internal
oscillator Calibration Word, located at 0x807FE,
will be erased. This location should be stored prior
to performing a whole Chip Erase and restored
afterward to prevent internal oscillators from
becoming uncalibrated.
Note:
Erasing Program Memory
Program memory must be erased before
writing any data to program memory.
Write 404Fh to NVMCON SFR
Set the WR bit to Initiate Erase
Delay P11 + P10 Time
CHIP ERASE FLOW
Done
Start
DS39907A-page 15