GRM155R60J225ME15D Murata, GRM155R60J225ME15D Datasheet - Page 120

• Manufacturer Part Number: GRM155R60J225ME15D
• Manufacturer: Murata

Specifications of GRM155R60J225ME15D

• Tolerance (+ Or -): 20%
• Voltage: 6.3VDC
• Temp Coeff (dielectric): X5R
• Operating Temp Range: -55C to 85C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 1mm
• Product Depth (mm): 0.5mm
• Product Height (mm): 0.5mm
• Product Diameter (mm): Not Requiredmm
• Capacitance: 2.2uF
• Package / Case: 0402
• Lead Free Status / RoHS Status: Compliant

6
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
Table A-6
Note 1: Nominal values denote the temperature coefficient within a range of 25 to 125D (for 5C)
118
No.
16
17
ERB Series Specifications and Test Method (1)
ERB Series Specifications and Test Methods
Continued from the preceding page.
Humidity
High Temperature
Load
Char.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
5C
Item
Nominal Values
(ppm/D) Note 1
The measured and observed characteristics should satisfy the
specifications in the following table.
The measured and observed characteristics should satisfy the
specifications in the following table.
Appearance
Capacitance
Change
Q
I.R.
Appearance
Capacitance
Change
Q
I.R.
0T30
Item
Item
Specifications
No marked defect
Within T5% or T0.5pF
(Whichever is larger)
10pFVCU30pF : QU350
10pFVCF30pF : QU275W
10pFVCF10pF : QU200W10C
1,000MΩ min.
No marked defect
Within T3% or T0.3pF
(Whichever is larger)
10pFVCU30pF : QU350
10pFVCF30pF : QU275W
10pFVCF10pF : QU200W10C
1,000MΩ min.
Max.
0.58
C: Nominal Capacitance (pF)
C: Nominal Capacitance (pF)
Specifications
Specifications
Y55
Y0.24
Min.
5
2
5
2
C
C
Capacitance Change from 25D (%)
Apply the 24-hour heat (Y10 to W65D) and humidity (80 to 100%)
treatment shown below, 10 consecutive times. Remove, let sit for
24T2 hours at room temperature, and measure.
Apply 200% (500V only 150%) of the rated voltage for 1,000T12
hours at 125T3D.
Remove and let sit for 24T2 hours at room temperature, then measure.
The charge/discharge current is less than 50mA.
Max.
0.40
-10
70
65
60
55
50
45
40
35
30
25
20
15
10
D
-5
5
0
Initial measurement
Y30
0 1 2 3 4 5 6 7 8 9 10 1112 13 14 15 16 17 18 19 2021 22 23 24
Humidity
90-98%
Y0.17
Applied voltage 50Vdc
Min.
Humidity
80-98%
Test Method
+10
- 2 D
One cycle 24 hours
Humidity
90-98%
Max.
Hours
0.25
Humidity
80-98%
Humidity90-98%
Y10
Y0.11
Min.
C02E.pdf
09.9.18