GRM155R60J225ME15D Murata, GRM155R60J225ME15D Datasheet - Page 135

• Manufacturer Part Number: GRM155R60J225ME15D
• Manufacturer: Murata

Specifications of GRM155R60J225ME15D

• Tolerance (+ Or -): 20%
• Voltage: 6.3VDC
• Temp Coeff (dielectric): X5R
• Operating Temp Range: -55C to 85C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 1mm
• Product Depth (mm): 0.5mm
• Product Height (mm): 0.5mm
• Product Diameter (mm): Not Requiredmm
• Capacitance: 2.2uF
• Package / Case: 0402
• Lead Free Status / RoHS Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
13
14
15
Mounting for testing : The capacitors should be mounted on the substrate as shown below using die bonding. when tests No.11 to 15 are performed.
GMD Series Specifications and Test Methods (1)
Continued from the preceding page.
Humidity
(Steady State)
Humidity
Load
High
Temperature
Load
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance No defects or abnormalities.
Capacitance
Change
D.F.
I.R.
Appearance No defects or abnormalities.
Capacitance
Change
D.F.
I.R.
Appearance No defects or abnormalities.
Capacitance
Change
D.F.
I.R.
R7 : Within 12.5%
R7 :
W.V. 25Vmin. : 0.05 max.
W.V. 16/10V : 0.05 max.
More than 1,000M or 50 · F
(Whichever is smaller)
R7 : Within 12.5%
R7 :
W.V. 25Vmin. : 0.05 max.
W.V. 16/10V : 0.05 max.
More than 500M or 25 · F
(Whichever is smaller)
R7 : Within 12.5%
R7 :
W.V. 25Vmin. : 0.05 max.
W.V. 16/10V : 0.05 max.
More than 1,000M or 50 · F
(Whichever is smaller)
Alumina substrate
In case Non "*" is added in PNs table, please refer to GMD Series Specifications and Test Methods (1).
Specifications
In case "*" is added in PNs table, please refer to GMD Series Specifications and Test Methods (2).
Gold land
GMD Series Specifications and Test Methods (1)
Gold wire
Set the capacitor for 500 12 hours at 40 2 C, in 90 to 95%
humidity.
Take it out and set it for 24 2 hours at room temperature, then
measure.
Apply the rated voltage for 500 12 hours at 40 2 C, in 90 to
95% humidity and set it for 24 2 hours at room temperature,
then measure. The charge/discharge current is less than
50mA.
A voltage treatment should be given to the capacitor, in which a
DC voltage of 200% the rated voltage is applied for one hour at
the maximum operating temperature 3 C then it should be set
for 24 2 hours at room temperature and the initial measurement
should be conducted.
Then apply the above mentioned voltage continuously for
1000 12 hours at the same temperature, remove it from the
bath, and set it for 24 2 hours at room temperature, then
measure. The charge/discharge current is less than 50mA.
Alumina substrate
Capacitor
Gold land
Die bond
Test Method
Gold wire
133
C02E.pdf
09.9.18
8