IDT5V9885CPFI IDT, Integrated Device Technology Inc, IDT5V9885CPFI Datasheet - Page 12

• Manufacturer Part Number: IDT5V9885CPFI
• Description: IC CLK GEN 3.3V EEPROM 32-TQFP
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Clock Generatorr

Specifications of IDT5V9885CPFI

• Pll: Yes with Bypass
• Input: LVCMOS, LVTTL, Crystal
• Output: LVCMOS, LVDS, LVPECL, LVTTL
• Number Of Circuits: 1
• Ratio - Input:output: 2:8
• Differential - Input:output: No/Yes
• Frequency - Max: 500MHz
• Divider/multiplier: Yes/Yes
• Voltage - Supply: 3.135 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 32-TQFP, 32-VQFP
• Frequency-max: 500MHz
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 5V9885CPFI

LOOP FILTER
the jitter transfer characteristics. The loop bandwidth can be extracted from the jitter transfer. A narrow loop bandwidth is good for jitter attenuation while a wide
loop bandwidth is best for low jitter generation. The specific loop filter components that can be programmed are the resistor via the RZ[3:0] bits, pole capacitor
via the CZ[3:0] bits, zero capacitor via the CP[3:0] bits, and the charge pump current via the IP[2:0] bits.
the fastest and easiest way to calculate the PLL loop bandwidth (Fc) given the programmable loop filter parameters is as follows.
phase margin thus compromising loop stability.
IDT5V9885C
3.3V EEPROM PROGRAMMABLE CLOCK GENERATOR
The loop filter for each PLL can be programmed to optimize the jitter performance. The low-pass frequency response of the PLL is the mechanism that dictates
The following equations govern how the loop filter is set.
Resistor (Rz) = 0.3KΩ + RZ[3:0] * 1KΩ
Zero capacitor (Cz) = 6pF + CZ[3:0] * 27.2pF (Eq. 16)
Pole capacitor (Cp) = 1.3pF + CP[3:0] * 0.75pF (Eq. 17)
Charge pump current (Ip) = 5 * 2
PLL loop filter design is beyond the scope of this datasheet. Refer to design procedures for 3-order charge-pump based PLLs. For the sake of simplicity,
PLL Loop Bandwidth:
Charge pump gain (Kφ) = Ip / 2π
VCO gain (K
M = Total multiplier value (See the PRE-SCALERS, FEEDBACK-DIVIDERS, POST-DIVIDERS section for more detail)
ωc = Rz * Kφ * K
Fc = ωc / 2π
Note, the phase/frequency detector frequency (F
Parameter
C P
CZ
RZ
IP
M * (Cz + Cp)
VCO
) = 950MHz/V * 2π (Eq. 20)
VCO
* Cz (Eq. 21)
(Eq. 22)
Bits
4
4
4
3
IP[2:0]
From PFD
µA
(Eq. 19)
DOWN
(Eq. 15)
(Eq. 18)
Charge Pump and Loop Filter Configuration
PFD
UP
) is typically seven times the PLL closed-loop bandwidth (Fc) but too high of a ratio will reduce your
Step
27.2
0.75
2
1
n
V
DD
Ip
Ip
12
Min
0.3
1.3
6
5
Cz
Rz
Cp
To VCO
INDUSTRIAL TEMPERATURE RANGE
12.55
Max
15.3
414
640
Units
K Ω
µA
pF
pF