ISL22416WFU10Z-TK Intersil, ISL22416WFU10Z-TK Datasheet
ISL22416WFU10Z-TK
Specifications of ISL22416WFU10Z-TK
Available stocks
Related parts for ISL22416WFU10Z-TK
ISL22416WFU10Z-TK Summary of contents
Page 1
... PART MARKING ISL22416UFU10Z* 416UZ ISL22416UFRT10Z* 416U ISL22416WFU10Z* 416WZ ISL22416WFRT10Z* 416W *Add “-TK” suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations) ...
Page 2
Block Diagram SCK SDO SDI INTERFACE CS SHDN Pin Descriptions MSOP/TDFN PIN NUMBER SYMBOL 1 SCK 2 SDO 3 SDI SHDN 6 GND ISL22416 V CC POWER-UP INTERFACE, ...
Page 3
... Thermal Resistance (Typical) 10 Lead MSOP (Note 2 +0 Lead TDFN (Notes Maximum Junction Temperature (Plastic Package +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below CC http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Temperature Range (Extended Industrial .-40°C to +125°C Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW 2.7V to 5.5V CC Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±3.0mA ...
Page 4
Analog Specifications Over recommended operating conditions, unless otherwise stated. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. (Continued) SYMBOL PARAMETER RESISTOR MODE (Measurements between ...
Page 5
Operating Specifications Over the recommended operating conditions, unless otherwise specified. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. (Continued) SYMBOL PARAMETER t Power-up Delay ...
Page 6
NOTES: (Continued) 8. DNL = [V(RW) – V(RW) ] LSB-1, for 127 the DCP register setting i-1 9. INL = [V(RW) – (i • LSB) – V(RW) ]/LSB for ...
Page 7
XDCP Timing (for All Load Instructions) CS SCK MSB SDI V W HIGH IMPEDANCE SDO Typical Performance Curves 100 V = 3.3V +125° 3.3V +20°C CC ...
Page 8
Typical Performance Curves 1.3 10k 1.1 0.9 0.7 0 5.5V CC 0.3 0.1 50k -0.1 -0.3 -40 - TEMPERATURE (°C) FIGURE TEMPERATURE ERROR 0 5.5V CC 0.2 0 -0.2 -0.4 ...
Page 9
Typical Performance Curves 300 250 200 150 50k 100 TAP POSITION (DECIMAL) FIGURE 11. TC FOR RHEOSTAT MODE IN ppm SIGNAL AT WIPER (WIPER UNLOADED) WIPER MID POINT MOVEMENT FROM 3Fh TO 40h FIGURE 13. ...
Page 10
Bus Interface Pins SERIAL CLOCK (SCK) This is the serial clock input of the SPI serial interface. SERIAL DATA OUTPUT (SDO) The SDO is an open drain serial data output pin. During a read cycle, the data bits are shifted ...
Page 11
Shutdown Mode The device can be put in Shutdown mode either by pulling the SHDN pin to GND or setting the SHDN bit in the ACR register to 0. The truth table for Shutdown mode is in Table 3. TABLE ...
Page 12
CS SCK SDI SCK SDI SDO Examples A. Writing to the IVR This sequence will write a new value (77h) to the IVR (non-volatile): Set the ACR ...
Page 13
Mini Small Outline Plastic Packages (MSOP -B- INDEX 1 2 0.20 (0.008) AREA TOP VIEW 0.25 (0.010) GAUGE PLANE SEATING PLANE - 0.10 (0.004) b -H- - 0.20 (0.008) SIDE VIEW 0.20 ...
Page 14
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...