ISL22449WFV14Z-TK Intersil, ISL22449WFV14Z-TK Datasheet
ISL22449WFV14Z-TK
Specifications of ISL22449WFV14Z-TK
Related parts for ISL22449WFV14Z-TK
ISL22449WFV14Z-TK Summary of contents
Page 1
... MARKING ISL22449UFV14Z* 22449 UFVZ ISL22449WFV14Z* 22449 WFVZ *Add “-TK” suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations) ...
Page 2
Block Diagram SCK SDI INTERFACE SDO CS SHDN Pin Descriptions TSSOP PIN SYMBOL 1 RW3 SCK 4 SDO 5 GND 6 RW2 7 RW1 SDI VCC 13 SHDN 14 ...
Page 3
... Thermal Information Thermal Resistance (Typical, Note TSSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . + 0.3 CC Maximum Junction Temperature (Plastic Package .+150°C Pb-Free Reflow Profile .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CC Recommended Operating Conditions Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C V Voltage for DCP Operation . . . . . . . . . . . . . . . . . . 2.7V to 5.5V CC Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -3mA to 3mA Power Rating ...
Page 4
Operating Specifications Over the recommended operating conditions unless otherwise specified. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. SYMBOL PARAMETER I V Supply Current ...
Page 5
Operating Specifications Over the recommended operating conditions unless otherwise specified. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. (Continued) SYMBOL PARAMETER V SHDN, SCK, ...
Page 6
Timing Diagrams Input Timing CS t LEAD SCK MSB SDI HIGH IMPEDANCE SDO Output Timing CS SCK t V MSB SDO ADDR SDI XDCP Timing (for All Load Instructions) CS SCK MSB SDI V W HIGH ...
Page 7
Typical Performance Curves 100 V = 3.3V +125° 3.3V +20° TAP POSITION (DECIMAL) FIGURE 1. WIPER RESISTANCE vs ...
Page 8
Typical Performance Curves 1.0 0 2. 5.5V CC 10k -0.5 -1.0 -40 - TEMPERATURE (ºC) FIGURE 7. END TO END R % CHANGE vs TOTAL TEMPERATURE SIGNAL AT WIPER (WIPER UNLOADED) ...
Page 9
SERIAL DATA INPUT (SDI) The SDI is the serial data input pin for the SPI interface. It receives device address, operation code, wiper address and data from the SPI external host device. The data bits are shifted in at the ...
Page 10
TABLE 3. SHDN pin SHDN bit High 1 Low 1 High 0 Low 0 SPI Serial Interface The ISL22449 supports an SPI serial protocol, mode 0. The device is accessed via the SDI input and SDO output with data clocked ...
Page 11
CS SCK SDI SCK SDI SDO Applications Information Communicating with ISL22449 Communication with ISL22449 proceeds using SPI interface through the ACR (address 1000b), IVRi (addresses 0000b, 0001b, ...
Page 12
Examples: A. Writing to the IVR: This sequence will write a new value (77h) to the IVR2(non-volatile): Set the ACR (Addr 1000b) for NV write (40h) Send the ID byte, Instruction Byte, then the Data byte ...
Page 13
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...