ATmega256RZAV Atmel Corporation, ATmega256RZAV Datasheet - Page 257

• Manufacturer Part Number: ATmega256RZAV
• Manufacturer: Atmel Corporation

Specifications of ATmega256RZAV

• Flash (kbytes): 256 Kbytes
• Max. Operating Frequency: 16 MHz
• Max I/o Pins: 54
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Crypto Engine: No
• Sram (kbytes): 8
• Eeprom (bytes): 4096
• Operating Voltage (vcc): 1.8 to 3.6
• Timers: 6
• Frequency Band: 2.4 GHz
• Max Data Rate (mb/s): 0.25
• Antenna Diversity: No
• External Pa Control: No
• Power Output (dbm): 3
• Receiver Sensitivity (dbm): -101
• Receive Current Consumption (ma): 16.0
• Transmit Current Consumption (ma): 17.0
• Link Budget (dbm): 104

Table 24-3.
2549N–AVR–05/11
Status Code
(TWSR)
Prescaler Bits
are 0
0x08
0x10
0x38
0x40
0x48
0x50
0x58
Status of the 2-wire Serial Bus
and 2-wire Serial Interface Hard-
ware
A START condition has been
transmitted
A repeated START condition
has been transmitted
Arbitration lost in SLA+R or NOT
ACK bit
SLA+R has been transmitted;
ACK has been received
SLA+R has been transmitted;
NOT ACK has been received
Data byte has been received;
ACK has been returned
Data byte has been received;
NOT ACK has been returned
Status codes for Master Receiver Mode
To/from TWDR
Load SLA+R
Load SLA+R or
Load SLA+W
No TWDR action or
No TWDR action
No TWDR action or
No TWDR action
No TWDR action or
No TWDR action or
No TWDR action
Read data byte or
Read data byte
Read data byte or
Read data byte or
Read data byte
Application Software Response
STA
0
0
0
0
1
0
0
1
0
1
0
0
1
0
1
ATmega640/1280/1281/2560/2561
STO
0
0
0
0
0
0
0
0
1
1
0
0
0
1
1
To TWCR
TWINT
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TWEA
X
X
X
X
X
X
X
X
X
X
X
0
1
0
1
Next Action Taken by TWI Hardware
SLA+R will be transmitted
ACK or NOT ACK will be received
SLA+R will be transmitted
ACK or NOT ACK will be received
SLA+W will be transmitted
Logic will switch to Master Transmitter mode
2-wire Serial Bus will be released and not addressed
Slave mode will be entered
A START condition will be transmitted when the bus
becomes free
Data byte will be received and NOT ACK will be
returned
Data byte will be received and ACK will be returned
Repeated START will be transmitted
STOP condition will be transmitted and TWSTO Flag will
be reset
STOP condition followed by a START condition will be
transmitted and TWSTO Flag will be reset
Data byte will be received and NOT ACK will be
returned
Data byte will be received and ACK will be returned
Repeated START will be transmitted
STOP condition will be transmitted and TWSTO Flag will
be reset
STOP condition followed by a START condition will be
transmitted and TWSTO Flag will be reset
257