ATmega88 Atmel Corporation, ATmega88 Datasheet - Page 22

• Manufacturer Part Number: ATmega88
• Manufacturer: Atmel Corporation

Specifications of ATmega88

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8.6
8.6.1
8.6.2
8.6.3
2545T–AVR–05/11
Register description
EEARH and EEARL – The EEPROM address register
EEDR – The EEPROM data register
EECR – The EEPROM control register
• Bits 15..9 – Res: Reserved bits
These bits are reserved bits in the Atmel ATmega48/88/168 and will always read as zero.
• Bits 8..0 – EEAR8..0: EEPROM address
The EEPROM Address Registers – EEARH and EEARL specify the EEPROM address in the
256/512/512 bytes EEPROM space. The EEPROM data bytes are addressed linearly between 0
and 255/511/511. The initial value of EEAR is undefined. A proper value must be written before
the EEPROM may be accessed.
EEAR8 is an unused bit in ATmega48 and must always be written to zero.
• Bits 7..0 – EEDR7.0: EEPROM data
For the EEPROM write operation, the EEDR Register contains the data to be written to the
EEPROM in the address given by the EEAR Register. For the EEPROM read operation, the
EEDR contains the data read out from the EEPROM at the address given by EEAR.
• Bits 7..6 – Res: Reserved bits
These bits are reserved bits in the ATmega48/88/168 and will always read as zero.
• Bits 5, 4 – EEPM1 and EEPM0: EEPROM programming mode bits
The EEPROM Programming mode bit setting defines which programming action that will be trig-
gered when writing EEPE. It is possible to program data in one atomic operation (erase the old
value and program the new value) or to split the Erase and Write operations in two different
operations. The Programming times for the different modes are shown in
Bit
0x22 (0x42)
0x21 (0x41)
Read/write
Initial value
Bit
0x20 (0x40)
Read/write
Initial value
Bit
0x1F (0x3F)
Read/write
Initial value
EEAR7
MSB
R/W
R/W
15
R
R
–
7
0
X
7
0
7
–
0
EEAR6
R/W
R/W
14
R
R
–
6
0
X
6
0
6
–
0
EEPM1
EEAR5
R/W
R/W
R/W
13
R
5
X
–
5
0
X
5
0
EEPM0
EEAR4
R/W
R/W
R/W
12
X
R
4
–
4
0
X
4
0
EEAR3
EERIE
R/W
R/W
R/W
11
R
3
0
–
3
0
X
3
0
EEMPE
EEAR2
R/W
R/W
R/W
ATmega48/88/168
10
R
–
2
0
X
2
0
2
0
EEAR1
EEPE
R/W
R/W
R/W
R
9
–
1
0
X
1
0
X
1
Table 8-1 on page
EEAR8
EEAR0
EERE
R/W
R/W
LSB
R/W
R/W
X
X
8
0
0
0
0
0
EEARH
EEARL
EEDR
EECR
23.
22