ATtiny13A Atmel Corporation, ATtiny13A Datasheet - Page 111

• Manufacturer Part Number: ATtiny13A
• Manufacturer: Atmel Corporation

Specifications of ATtiny13A

• Flash (kbytes): 1 Kbytes
• Pin Count: 8
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 6
• Ext Interrupts: 6
• Usb Speed: No
• Usb Interface: No
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.06
• Eeprom (bytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 2
• Pwm Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

17.7.2
Table 17-13. High-Voltage Serial Programming Instruction Set for ATtiny13A
8126E–AVR–07/10
Instruction
Chip Erase
Load “Write
Flash”
Command
Load Flash
Page Buffer
Load Flash High
Address and
Program Page
Load “Read
Flash”
Command
Read Flash Low
and High Bytes
Load “Write
EEPROM”
Command
High-Voltage Serial Programming Instruction set
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
SDI
SII
SDO
0_ bbbb_bbbb _00
0_bbbb_bbbb_00
0_1000_0000_00
0_0100_1100_00
0_0001_0000_00
0_0100_1100_00
0_0000_1100_00
0_0000_0000_00
0_0000_000a_00
0_0001_1100_00
0_0000_0010_00
0_0100_1100_00
0_0000_1100_00
0_0000_0000_00
0_0001_0001_00
0_0100_1100_00
0_0111_1100_00
0_0111_1000_00
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
Instr.1/5
Table 17-12. High-voltage Reset Characteristics
The instruction set is described in
Supply Voltage
V
4.5V
5.5V
6. Wait until Vcc actually reaches 4.5 - 5.5V before giving any serialinstructions on
7. Exit Programming mode by power the device down or by bringing RESET pin to 0V.
CC
SDI/SII.
p_pppp_pppx_xx
0_0000_0000_00
0_0110_0100_00
0_eeee_eeee_00
0_0010_1100_00
0_0000_0000_00
0_0110_0100_00
0_0000_000a_00
0_0001_1100_00
0_0000_0000_00
0_0111_1100_00
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
Instr.2/6
Instruction Format
RESET Pin High-voltage Threshold
0_dddd_dddd_00
0_0000_0000_00
0_0000_0000_00
0_0000_0000_00
0_0110_1100_00
0_0011_1100_00
0_0110_1100_00
0_0110_1000_00
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
x_xxxx_xxxx_xx
Table
V
Instr.3
HVRST
12V
12
17-13.
q_qqqq_qqqx_xx
0_0000_0000_00
0_0000_0000_00
0_0111_1101_00
0_0110_1100_00
x_xxxx_xxxx_xx
Instr.4
Minimum High-voltage Period for
Latching Prog_enable
Operation Remarks
Wait after Instr.3 until SDO goes
high for the Chip Erase cycle to
finish.
Enter Flash Programming code.
Repeat after Instr. 1 - 5 until the
entire page buffer is filled or until all
data within the page is filled. See
Note 1.
Wait after Instr 3 until SDO goes
high. Repeat Instr. 2 - 3 for each
loaded Flash Page until the entire
Flash or all data is programmed.
Repeat Instr. 1 for a new 256 byte
page. See Note 1.
Enter Flash Read mode.
Repeat Instr. 1, 3 - 6 for each new
address. Repeat Instr. 2 for a new
256 byte page.
Instr 5 - 6.
Enter EEPROM Programming
mode.
Instr 5.
100 ns
100 ns
t
HVRST
111