ATtiny13A Atmel Corporation, ATtiny13A Datasheet - Page 45

• Manufacturer Part Number: ATtiny13A
• Manufacturer: Atmel Corporation

Specifications of ATtiny13A

• Flash (kbytes): 1 Kbytes
• Pin Count: 8
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 6
• Ext Interrupts: 6
• Usb Speed: No
• Usb Interface: No
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.06
• Eeprom (bytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 2
• Pwm Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

9. Interrupts
9.1
8126E–AVR–07/10
Interrupt Vectors
This section describes the specifics of the interrupt handling as performed in ATtiny13A. For a
general explanation of the AVR interrupt handling, refer to
page
The interrupt vectors of ATtiny13A are described in
Table 9-1.
If the program never enables an interrupt source, the Interrupt Vectors are not used, and regular
program code can be placed at these locations.
The most typical and general program setup for the Reset and Interrupt Vector Addresses in
ATtiny13A is:
Vector No.
Address Labels Code
0x0000
0x0001
0x0002
0x0003
0x0004
0x0005
0x0006
0x0007
0x0008
0x0009
;
0x000A
0x000B
0x000C
0x000D
12.
...
10
1
2
3
4
5
6
7
8
9
RESET: ldi
Reset and Interrupt Vectors
...
out
<instr>
Program Address
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
rjmp
sei
...
SPL,r16
0x0000
0x0001
0x0002
0x0003
0x0004
0x0005
0x0006
0x0007
0x0008
0x0009
xxx
...
RESET
EXT_INT0
PCINT0
TIM0_OVF
EE_RDY
ANA_COMP
TIM0_COMPA
TIM0_COMPB
WATCHDOG
ADC
r16, low(RAMEND); Main program start
Source
RESET
INT0
PCINT0
TIM0_OVF
EE_RDY
ANA_COMP
TIM0_COMPA
TIM0_COMPB
WDT
ADC
Comments
; Reset Handler
; IRQ0 Handler
; PCINT0 Handler
; Timer0 Overflow Handler
; EEPROM Ready Handler
; Analog Comparator Handler
; Timer0 CompareA Handler
; Timer0 CompareB Handler
; Watchdog Interrupt Handler
; ADC Conversion Handler
; Set Stack Pointer to top of RAM
; Enable interrupts
Table 9-1
“Reset and Interrupt Handling” on
EEPROM Ready
Interrupt Definition
External Pin, Power-on Reset,
Brown-out Reset, Watchdog Reset
External Interrupt Request 0
Pin Change Interrupt Request 0
Timer/Counter Overflow
Analog Comparator
Timer/Counter Compare Match A
Timer/Counter Compare Match B
Watchdog Time-out
ADC Conversion Complete
below.
45