ATtiny13A Atmel Corporation, ATtiny13A Datasheet - Page 73

• Manufacturer Part Number: ATtiny13A
• Manufacturer: Atmel Corporation

Specifications of ATtiny13A

• Flash (kbytes): 1 Kbytes
• Pin Count: 8
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 6
• Ext Interrupts: 6
• Usb Speed: No
• Usb Interface: No
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 4
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.06
• Eeprom (bytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 125
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 1
• Output Compare Channels: 2
• Pwm Channels: 2
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

11.9.2
8126E–AVR–07/10
TCCR0B – Timer/Counter Control Register B
• Bits 1:0 – WGM0[1:0]: Waveform Generation Mode
Combined with the WGM02 bit found in the TCCR0B Register, these bits control the counting
sequence of the counter, the source for maximum (TOP) counter value, and what type of wave-
form generation to be used, see
Timer/Counter unit are: Normal mode (counter), Clear Timer on Compare Match (CTC) mode,
and two types of Pulse Width Modulation (PWM) modes (see
Table 11-8.
Notes:
• Bit 7 – FOC0A: Force Output Compare A
The FOC0A bit is only active when the WGM bits specify a non-PWM mode.
However, for ensuring compatibility with future devices, this bit must be set to zero when
TCCR0B is written when operating in PWM mode. When writing a logical one to the FOC0A bit,
an immediate Compare Match is forced on the Waveform Generation unit. The OC0A output is
changed according to its COM0A[1:0] bits setting. Note that the FOC0A bit is implemented as a
strobe. Therefore it is the value present in the COM0A[1:0] bits that determines the effect of the
forced compare.
A FOC0A strobe will not generate any interrupt, nor will it clear the timer in CTC mode using
OCR0A as TOP.
The FOC0A bit is always read as zero.
Bit
0x33
Read/Write
Initial Value
Mode
0
1
2
3
4
5
6
7
1. MAX
2. BOTTOM = 0x00
WGM02
0
0
0
0
1
1
1
1
Waveform Generation Mode Bit Description
FOC0A
W
7
0
WGM01
= 0xFF
0
0
1
1
0
0
1
1
FOC0B
W
6
0
WGM00
0
1
0
1
0
1
0
1
Table 11-8 on page
R
5
–
0
Timer/Counter
Mode of Operation
Normal
PWM
(Phase Correct)
CTC
Fast PWM
Reserved
PWM
(Phase Correct)
Reserved
Fast PWM
R
4
–
0
WGM02
R/W
73. Modes of operation supported by the
3
0
OCRA
OCRA
OCRA
0xFF
0xFF
0xFF
TOP
“Modes of Operation” on page
CS02
–
–
R/W
2
0
Update of
Immediate
Immediate
OCRx at
CS01
R/W
1
0
TOP
TOP
TOP
TOP
–
–
CS00
R/W
0
0
Set on
TOV Flag
BOTTOM
BOTTOM
MAX
MAX
MAX
TOP
TCCR0B
–
–
(1)(2)
64).
73